S-10CREWCAB.NET

S10Wheels

I need these parts for a late model ('03) 4.3. The oil cooler lines from the filter adapter to
the radiator for a 2WD, can be good or bad (leaky), must be intact, need to experament on.
The MAF must be good & pretty clean, my truck needs one.

S10Wheels

Thought I'd let you know about my fan changeover last week from a Flex-a-lite 210, to an Intrepid fan. After I removed the 210's, I could see the 2 fans side by side and compare. The Intrepid fan was about 3-5 lbs.heavier because the shrowed is thicker and more ridged and the motors are larger and "...

S10Wheels

http://forums.s-10crewcab.net/viewtopic.php?f=3&t=7993 One of my LONG install threads. Pics on page 2. I didn't use a gasket or anything, just slide it in there. Tight fit. Bent some fins on the outside doing so. One of my motors went bad, out of balance. The fan was mounted slightly loosely, that ...

S10Wheels

My bottom mount is much like yours, using the tabs, etc. and the top mount is the same. But I'm wondering about where the plastic shrowed will contact the edges of the core? The Flex. 210 has a rubber gasket (like a door or trunk lid) around the edge of the shrowed to seal & protect the fins at the ...

S10Wheels

I'm about to change my Flex. 210 to a set of Intrepid fans, not because the Flex fans didn't work, they did good for the past 3 1/2 years. But because the intrepid fans are supposed to move more air, be quieter, and be smoother (balanced better) and to be honest, I like to mess with my truck. My que...

S10Wheels

nebby58 wrote:Hey Cajun, on a scale of 1 to 10, how hard was it?

I'd say, on a scale of 1-10, it's a 1 or a 2 as long as you don't drop anything in there you can't pick back out. Then it becomes a lot of work. Hey Cajun-did you lok-tite the screws back in?

S10Wheels

I just finished the cut down version described above and WOW :shock: what a difference! The truck jumbs right out of the hole on acceleration from a dead stop now. This has to be the best mod for the buck. A close second would be the poly front sway bar bushings. Thanks for your help guys! And it g...

S10Wheels

...ok I have the torx screws out , opened the throttle but the blade won't turn lose. What am I doing wrong? I can't seem to find the step by step thread fro thr t blade mod. Found it, no help. The thread says it just slides out. I've tapped on the blade in the open position with a wooden dowel but...

S10Wheels

Sorry it took so long to get back-unexpected crap-you know how it goes! Anyway, cutting off the throttle blade only in part was the right thing to do. I cut the air diffuser about 2/3 of the way, leaving a 4-5mm. lip then shaping & smoothing the lip. In a parking lot or slow maneuvering it’s like it...

S10Wheels

Glad to hear it is a success. The "little touchy" I experienced was only in low range. I was able to adapt to that. It is a better throttle response. Less dulled. The big difference is not as noticeable on the install. You can really feel it once you become acustomed to the modded blade and swap ba...

S10Wheels

I got around to doing the throttle mod. Today, here’s how it went. I figured it made sense to cut it off only partway, the main complaint people had was a “jumpy”over sensitive throttle at slow speeds, a small bit of a diffuser would make it much easer and safer to maneuver around parking lots & suc...

S10Wheels

I didn't take the throttle body off. It can be removed without full disassembly. I know, but after that @%&# cruise cable, and the throttle cable it's only 5 bolts, and then I can clean it real good & change the throttle blade without dropping anything down the intake (including a bunch of carb. cl...

S10Wheels

I finally got around to putting on your spare AD 244 130a, it went on like it's supposed to (no problems) and works fine, not like the aftermarket I had on it that would flicker the dash light even though I put a new reg in it! It will be my spare now, and yours will live on the truck. I agree, STIC...

S10Wheels

I am taking off my throttle body to change the throttle blade & clean it. But I can't get the cruise cable off, the GM-SI manual says not to remove the "C" clip or unscrew the adjuster, just use a flat blade screwdriver to pry it off, but if I pry too hard, I'm afraid it'll break. Is there a better ...

S10Wheels

How'bout the plastic trim panel under the rear window?

S10Wheels

I need the plastic trim panel (charcoal, or GM graphite in color) that goes on the back wall, below the rear window in a 3 door ext. cab or about any gen. II pickup. The panel that everybody takes off to fit a sub. box behind the rear seat in a CC. Must be clean & unbroken. If you have one to sell, ...

S10Wheels

I have the dash apart on my 03 and have taken out the 3 screws from the sides of the radio. It comes out about an inch and a half and stops . Am I not pulling hard enough or what else is there holding it? After the bolts are out, the radio should about fall out. The only things that can be holding ...

S10Wheels

A 3rd. brake light from a Blazer, Van or even one of those glass mount accessory lights.

S10Wheels

S10Wheels

I have tried sights that say “free” mp3 downloads like Imesh, Bearshare, etc. Which I did find & download the songs I was looking for. They are in a .WMA format which is OK cause my mp3 player, computers and my car HU can read .WMA’s . But, these files can only be played on the computer that they wh...

S10Wheels

Opinions/Advice on Bazooka Bass tube or other sub suggestion Loved mine. Just enough thump to richen the experience. No room for it in the new ride. Hi Brule, there will be a PM for you soon. That's what kind of sound I want without taking room out of the cab. What size did you have? It had a small...

S10Wheels

I know a number of you have them, how are they? All I want is to is add some low end and make my system. sound better - don't need a Boom!-Boom!-Boom system. 6 or 8" Bazooka tube? I'm going to be without my truck for 2 or 3 weeks, so I can think of things that need to be done to it. Ho-Hum I'm alrea...

S10Wheels

OK, your "ace in the hole" AD244 is a 130A junk yard, 4 wire AD right? and it works fine on your 2002 S-10 right? no batt. light stuff? Sounds OK, let's do it! You pay your shipping, and I'll pay mine. I think USPS prioirty would be the best deal now, or is there a cheaper way? I'd rather save the p...

S10Wheels

Still got that DR44G ? Is it a two wire regulator? If it is, wanna trade for my AD244 ace in the hole alternator? Check out my thread in the classifieds. Yea, it is a 2 pin reg. 145A off an '06 Sierra with 43000 mi. The only thing is the plastic cover was cracked & repaired on the bottom. (no big d...

S10Wheels

Sounds like you have a good plan of attack. Examine the regulator closely before installation. A good regulator will have lots of cooling fins. Well, I got the new reg. from Springhill, it is a Transpo D200XHD with a 14.8 Vset it has 8 thin fins, in a Transpo box, so I know it is just what I ordere...

S10Wheels

Hey thanks, Henry J, I'm just going to wait & see what I get! Well it is a DR 44G, I'm a stubborn old cuss though, I wanted an AD 244, a few days later I ran into a 200A AD 244 at a price I could not refuse. It was a clone (unmarked) case with a chrome sticker that say's 200A, made in USA, no numbe...

S10Wheels

Doing a fall clean out, have some stuff to sell off. A DR 44G, 145 amp. alternator, 2 wire plug, came from a '06 GM full size truck. (DR44G SOLD) And a CS 130D 100 amp. (stock) alt., later ('98) S-10.) newly been rebuilt. make me an offer for the CS 130D. A complete console, that's like new, w/all b...

S10Wheels

Hey thanks, Henry J,
I'm just going to wait & see what I get!

S10Wheels

You don't need an adapter to install the AD244 alternators. They are plug-n-play. All you need is the longer belt. Search for the bigger Alternator thread and it has all the details. The above adapters linked are for the CS144. I would not recommend using one of those. The AD244 is a much better op...

S10Wheels

I want to put an AD-244 145A on my truck ('03 S10 4.3) It now has the factory CS on it. In my haste to find one, I ordered, what I think will be a 2 wire plug, it came out of an '06 Chevy, Silverado V8. At this time I can't say for sure (I won't get it for a week or so) but if I did screw up, can I ...

S10Wheels

This is why I was thinking of putting a switch in the a/c signal wire. Let's say I got off the interstate & forgot to flip the fan switch (I doubt that would happen, but my old brain forgets once in a while) the fans would still come on for rad. temp.

S10Wheels

The setup is Flex-o-lite 210 fan, fans wired together, and a VSC controller. Works good no problems. Need your opinion for a little mod. I was thinking of. The fans are running (as they're supposed to) with the A/C on, including on the interstate going 60 + mph. The question - If i put a switch in t...

S10Wheels

That's exactly what I needed to know-thanks, I'll expect temps. ranging around 180-200+ were having some warm temps here, 70's-80 by afternoon.

S10Wheels

Brule, I got my X-gauge reprogrammed Scangauge II back today. I will put it back in the truck first thing in the morning and I'll have to wait a couple of days till I can really play with it. First comes Trans. temp. (whats the norm & high temp.?), then HP & torque, then A/F ratio, and ..... :woohoo:

S10Wheels

The transmission temperature gauge has been consistently within a couple degrees. I have not added any other gauges. Maybe I'll look through the choices during the holiday break. Add this one to your Xmas list if it is not too late. It is a good one. My Scangauge II is already there, it was deliver...

S10Wheels

I finally have my Scangauge II all packed & ready to send off for the upgrade, I already miss it every time I get in my truck and see that naked connector. My strenth is in how overjoyed & excited you are with the X-gauge upgrade, it'll be worth a few weeks without it.
S10Wheels

S10Wheels

Just got a call from Scangauge / Linear Logic. They broke my mount :( I told them that it was no big deal and I would fab a new one. They actually have to make the upgrade internally and the case must be separated. I glued the bracket on mine and the case could not be separated. There is a line aro...

S10Wheels

What did you insure it for $ 200?

S10Wheels

Hey!, HenryJ, My Scangauge II is going back for the X gauge mod. too. The form is filled out, I've got the box to send it in & the address label printed. I've got one problem though, it's so good that I've gotten to depend on it. and don't want to be without it (for even a few weeks! )(my problem). ...

S10Wheels

I've got on my list of stuff to buy for the truck one of those AeroforceTech gauges. The only real differences are the form factor, the price, and the ability to read trans temp. I can see both being some VERY handy gadgets! I have ordered a Scangauge II, but I can't see how (with the option) it co...

S10Wheels

From where? I need a stock S-10 Drv. side mirror.

S10Wheels

I just put in an autodimm/compass inside mirror from a Mercury grand marque. I would like to find a left side mirror that autodimmes also, I think that any cars or trucks (including S-10's) with that option had 'em. Anybody ever hear of this?

S-10CREWCAB.NET

Search found 41 matches

WTB-OEM MAF sensor & your good or bad oil lines

Re: To anybody that adapted and mounted an OEM fan. LS x, et

Re: To anybody that adapted and mounted an OEM fan. LS x, et

Re: To anybody that adapted and mounted an OEM fan. LS x, et

To anybody that adapted and mounted an OEM fan. LS x, etc.

Re: Did the throttle blade today-results

Re: Did the throttle blade today-results

Re: Did the throttle blade today-results

Did the throttle blade today-results

Re: Did the throttle plate mod. today

Did the throttle plate mod. today

Re: R & R cruise control cable

Henry J's spare AD 244

R & R cruise control cable

Re: Crew Cab Front Seats and other Parts

Wanted-Plastic trim under rear wondow

Re: radio stuck?

WTB- center (roof mount) brake light - FOUND ONE - DELETE

Where do you get your music?

Re: Bass tube type sub/amps

Bass tube type sub/amps

Re: Alternator wireing advice

Re: Alternator wireing advice

Re: Alternator wireing advice

Re: Alternator wireing advice

F/S CS 130d 100 A alt. (stock S-10) + other stuff

Re: Alternator wireing advice

Re: Alternator wireing advice

Alternator wireing advice

e-fan or no e-fan? HJ- I need your opinion

Re: auto dimm side mirror

autodimm side mirror???