S-10CREWCAB.NET

Jongo88

Well guy's I no longer own a crew.. I traded it in on a 2012 Jeep Wrangler.... It was a good ride but time to move on...

Jongo88

To bad it don,t work with tinted windows and a topper....

Jongo88

That is a bad ass lookin truck!!!!!

Jongo88

4wd IFS is way more crucial to ride height then strait axle front ends... You only have a 1.5 inch list to play with before you get to the first mud hole and snap your cv axles.... Just set your ride height and forget it....

Jongo88

I really don't think they will fit. You have the tube diameter but not the rubber sock diameter. And it would be hell to adjust them to keep your alignment in check. Every time you change them ( they all leak over time ) so will your alignment...

Jongo88

Show off..... lol

Jongo88

NICE!!!!!

Jongo88

http://ocala.craigslist.org/pts/3960751085.html

Jongo88

I changed mine too and they are very easy to change. Just make sure you have a left and right side when you buy them..
If your handles are good you can buy a key for them too.

Jongo88

Replaced my drivers side power window motor.

Jongo88

So I just replaced my u joint. The Part# 2-1153 is indeed the right u joint.... One thing I want to point out is just don't jamb your drive shaft into the transmission without cleaning the yoke as mine had rust on it and would kill the seal if left that way. I just cleaned it up with 1000 grit sand ...

Jongo88

So I replaced my rear end with a zr2 rear. Everything bolted right up like every one says. Then I got to the drive shaft and the u joint caps are to small. So I wrapped the caps with shimming stock to get by. All I have to go to is the shitty chain stores that don't know anything but stock stuff. I ...

Jongo88

They are good for gates too... I have my gate and two garage doors on mine...

Jongo88

Is that delevered to Florida??? Welcome to the site...

Jongo88

Sounds like a major pain just to get the stock tow/haul mode with the torque management still killing your performance. . I like it programmed to what ever you want it to do. I have the stock switch but my tow/haul does exactly what I want. And the best thing it is plug and play.

Jongo88

No dash light. For that you need the BCM. I forget which pin it is. He sent a 6 inch wire with the female pin that I had to install into the PCM plug. The wire then goes to the tow/haul switch. The other side of the switch wire goes to ground. When you push the switch it changes to the other trans t...

Jongo88

Whats to tell?? You send him your PCM and he can make it do just about anything you want. I sent him mine for a tune and he added the tow/haul to it. I picked up a tow/haul switch from the junk yard ran one wire to the PCM and bingo. I have a tow/haul.

Jongo88

That one is plastic... I'm at work at the moment... You want an aluminum one... I got one cheaper that that.

Jongo88

You need to replace the distributor. The best bet is replace it with a new aluminum one off e bay. I did and like it. They come fully loaded with a brass cap. Plug and play. I bought two of them and put one in my crew. The other one was for my wife's Jimmy but she traded it in so It's just sitting h...

Jongo88

I have three of them. One stock one, one cut half and one cut all the way off. I put the one that's cut all the way off in and the trans shifts way to soon when you are getting into it. It will shift into over drive at 52. Then you have to push the skinny peddle harder to down shift to get going aga...

Jongo88

I have the tow/haul working in my truck... We have a tuner guy on my other forum that can hook you up. There is no need to change out the BCM eather....

Jongo88

How lucky.. I have been looking for a zr2 rear for years..

Jongo88

I had to do this on my Crew...

Jongo88

What about the ABS light?? I havent messed with that yet. read somewhere pulling the fuse for abs on the driver side dash fuse box fixes it. if not im going to pull the dash circuit board off and jump the positive side of the abs led to the check gauses light. that way everything lights up as norma...

Jongo88

What about the ABS light??

Jongo88

Just drop the head liner down on that side. It runs across the front of the roof. You should be able to pull the plastic piece out and get it with needle nose pliers..

Jongo88

I tried a puller and gave up. I just used my 3 inch air cut off wheel and cut it on one side almost all the way to the shaft. Popped it with a chisel it the cut and it fell off.... Very easy this way...

Jongo88

I picked it up for 75 bucks... It was even the right color too.... Lucky me.

Jongo88

Nice looking truck. I have a very nice new looking powder coated black box in my shop. I went topper.

Jongo88

It looks like the outline of a dead body on the floor....lol

Jongo88

Yep that's the size. When I put them side by side to my old 31's they were the same size. But all tires may be different sizes... This is the perfect combo for me. I have no rub anywhere. I can stand it cross ways in a ditch with one front and one back wheel off the ground with no rub. I can turn it...

Jongo88

All 4 are 6 and 1/8 back spacing...

Jongo88

I have 1.25 spacers in front and 2.5 in back on 16 x 8 Trans am wheels.

Jongo88

They came from the junk yard.. lol. I have not had any problems without them so I said if it's not broke don't fis it..lol
I'm only running 31 10.50's though...

Jongo88

I had the full size ones on my truck but the rubber rotted off them... All that is left is the mettel cups....

Jongo88

mars2878 wrote:i have stock 00 camaro 16" rims on crew cab.
without spacers or rubbing.
i'm currently running 235/65/16.
its what came on the rims when i got them.

That would be good if he needed new wheels. But he is looking for a spare....

Jongo88

Any 4x4 s10 wheel will fit. Blazer, Jimmy, S10, Sonoma, Jimmy and bravada.

Jongo88

I had some but the rotted off... Been running without them for some time now..

Jongo88

When I get the brush guard I will make them functional... I have the hitch in the back. I know my limits and been lucky so far.

Jongo88

I moved the tow hooks to the bottom just for looks.... I would never use them...

Jongo88

Spent a couple of hours on the Rhino tail light guards removing the flaking powder coat and prepping them for painting. I used a Dewalt grinder with a 80 grit flapper wheel, a wire wheel on a drill and a Dremel barrel sander and hit it with a couple coats of primer. I'm unsure on what to use as the...

Jongo88

Jongo88

You say you replaced your clutch??? I bet you got the extreme duty one... They are way to strong. I made the same mistake and it started to rip my cloth from under my hood.... I returned it for a stock one and was happy until in went to a e fan.

Jongo88

That brush/grill guard would look good on my truck!!!!

Jongo88

No. The pump is just under the back of the cab...

Jongo88

That's funny.. I ran out of gas and can only get 16 in mine... Normal fill ups are 13...

Jongo88

Iif were me, before I had to spend that much money I would just get a Blazer tank and remove the spare tire and be done with it.

Jongo88

I'm really starting to like the look of the GMC grill, headlights & hood better than the S10 version. It looks much cleaner and simpler to me. The GMC crew cab looks great in black! Steve Thanks Steve.. It took me a long time to find a black GMC... Then I removed all the chrome off it. I replaced t...

Jongo88

Welcome to the site..

Jongo88

Jongo88

What is the two long leaf springs from?

Jongo88

Spammer!!!!!

Jongo88

You don't dismantle the dash to replace the harness eather...

Jongo88

I have two uncut wire harnesses if anyone needs them.. This makes it plug and play...

Jongo88

Does it look like it has the very same cab as ours?? It kinda looks like it to me...

Jongo88

The Blazers were exported to Europe and the production Crew Cab trucks share the same forward wiring harness. Provisions for the auto dimming headlamps are in the electrical center. The picture shown above is similar to the newer S-10. Production in South America continued beyond that of the US. Th...

Jongo88

A good wack with a BFH....

Jongo88

All you need to do now is raise the step bars.... Looks good....

Jongo88

Yes, and I must say I like them...

Jongo88

I tried the split boots on my old Blazer and the seem hit the shock.... The shock is very close to the boot. I just replaced the shaft and never had a problem again...

Jongo88

I would not get the Goodyear Wrangler Authority.. I just bought them for my truck. I was back 5 times to get them balanced. They had weights the size of bricks on them. They were out of round big time. They replaced two of them and the new ones were just as bad. I made them give my money back and we...

Jongo88

I fixed mine when I made my shackles.... I tried to move the springs from right to left and it was the same.
So when I made my shackles I made the drivers side a little bit taller...It's been like that for about two years now.

Jongo88

I think they all have the chevy lean...

Jongo88

Much better!!!!

Jongo88

You know that I that I try to think back I don't really remember if I did the cuts before or after the bl.
But I think I did them before because I was tryin to see if I could get away without the bl...

Jongo88

All my info is in my sig.. I started off by getting new tires and 1.5 inch T bar tweek and shackles. Then I bought shocks and spacers for the back. Then I had to do the skid cut outs. Then came the body lift. Then I bought 2.5 spacers for the back and moved the 1.25 to the front. I seems for every m...

Jongo88

I did the 31's for the same reasons... You will be happy as I am. My truck handles like stock it mite be better. I can go through ditches drive over stuff crossways and never have the tires rub in anyway. I'm on my second set of tires now and if I thought I needed bigger I would of got them this tim...

Jongo88

No flairs... I have no idea about the 33's. I myself would not go bigger than 31's. I drive a lot and I know that the 33's would kill my gas millage... I do know if you run the 33's you will have to do the skid cuts in the back too. With the 31's you only need them in the front. I hope this helps yo...

Jongo88

I do with the cuts... I can go anywhere with no rub now... Without the cuts the tires would not only rub but would hit the back of the fenders.

Jongo88

I copyed this from my other forum... http://www.s10planet.com/forum/attachme ... 1336675660
can you tell I did the skid cuts???

Jongo88

I had to to get 31's to work... Does that help??? lol

Jongo88

You can if you stay on the street and don't turn sharp. Your front tires will rub the back of the fenders...
I did for three weeks...

Jongo88

They are an exact replacement.. Just built the right way..

Jongo88

They used to be Power Permormance but they are now proforged.
http://www.proforged.com/

Jongo88

Here is a crew with TA wheels and is lifted with 265 70 16's..

Search found 374 matches