S-10CREWCAB.NET

tomtk

engine oil cooler lines. I have some seeping after a radiator swap and sure would like to pick up some Viton orings the correct size before I take it apart.

tomtk

.......Ya got lucky mine was the poppet style funny in CA they would have replaced them as defective Um, you ain't in CA and that was state specific. It looks like you don't need any help from me concerning the CC or deciding whether you should keep it or not. I merely tried to answer your question...

tomtk

I bought my 2002 and have replaced more parts by 58500 miles than in 165,000 on my 84........... e brakes all four rotors rear back plates rusted thru Did you regularly use your e brakes? If, not then there is the reason. Did you replace them and the rear rotors yourself? If, you had it done why di...

tomtk

I had a 1984 2wd S10 and only fed it brakes, hoses, belts, exhaust and radiators. I bought my 2002 and have replaced more parts by 58500 miles than in 165,000 on my 84 so far Motor encoder just out of 36K warrenty e brakes all four rotors rear back plates rusted thru left front CV axle all 4 ball jo...

tomtk

Like I said the diameter of the hub where the oring would have went was a good .030 smaller. I tried the oring in there BUT it did not seal anything and just flopped around loose in the space. Every other car I have helped change a bearing hub on had no seal there.

tomtk

Typo above meant .030 smaller

tomtk

Replaced left hub as sound got louder on right turns and that shifted wieght to the left front. I used the above hub Steve posted. I did swap one of the ABS wire brakets for the one that cam on it to route wire better. It was the one that has the locating tab on the upeer control arm. Hubs are sligh...

tomtk

Ordered pair of US made hubs from http://www.shop.synergyoffroad.com/product.sc?categoryId=35&productId=5 Does anybody know if the above US made hubs come with the oring seals? I am leaning toward replacing left side first as when turning right it gets louder. While I wait on the UPS truck I am goi...

tomtk

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=38878 I bolted the chain attacment with some old lug nuts on upside down and hammered and rotated around the 3 points where hub attached. I already had this slidehammer I bought it on markdown couple years ago as a return for like $15 ...

tomtk

Tore down the left front and used a 13lb slide hammer attached to lugs tugged the hub right out.

Still no UPS tracking status .....I bet once the tempature drops to arctic ranges the UPS delivery will be here

tomtk

Synergy Offroad S-Series Wheel Bearings http://shop.synergyoffroad.com/images/1170737215669469875113.jpeg Steve Drove it some more today getting much louder I am convinced the left side is the one to swap first. Do those come with the seal/oring? Does he usually have them in stock? I am chompin at ...

tomtk

Ordered pair of US made hubs from http://www.shop.synergyoffroad.com/product.sc?categoryId=35&productId=5 Does anybody know if the above US made hubs come with the oring seals? I am leaning toward replacing left side first as when turning right it gets louder. While I wait on the UPS truck I am goin...

tomtk

I will jack the truck up and try to see if one is sloppy. I REALLY would like to do just one till spring its cold up here How fast do they get worse if I run it abit longer will it get so sloppy that its obvious which one is bad?? I have read both versions of which one to replace I have seen both vi...

tomtk

its like 10F outside and I just want to swap out the bad one till we get to the two weeks of summer here in Michigan

tomtk

truck only has 60K city miles never goes off road. Has anybody used these bearings???

Is there a rule of thumb if it howls turning in a direction to point to which side is bad??

http://www.shop.synergyoffroad.com/prod ... roductId=5

tomtk

2002 crew cab History 1. drivers side CV axle replaced with new NAPA shaft 3 months ago 2 all 4 ball jints replaced with MOOGs 2 months ago I did the ball joints after shop did CV axle because they had left off cotter pin on nut for lower ball joint and I did not trust them anymore. Now I have a how...

tomtk

TRW, MOOG or McQuay Norris? What brand is worth it for a city truck in the snow with stock tires?

tomtk

I live in Michigan I do not want to wait till winter (labor rates go up with the cold) and have further troubles so I will have it replaced ..I am told the NAPA boots last longer Besides I could not find that grease that looks like GMs all the small packets had Moly inthem around here how much is lo...

tomtk

and I found a shop that will install it for $85...sounds like a job I will pay for. For that much its not worth my time to do it.

tomtk

do torsion bars have to be unloaded to pull steering knuckle and remove the half shaft???

tomtk

went thru this before on the great harley versus syn oil debates about ten years ago. Harley condemed syn oils as unsuitable...I selected Castrol Syntec 20W50...recently I noticed that Castrol touts their 20W50 Syntec as having the higher levels of ZDDP that they recommend it for classic muscle cars...

tomtk

the Delvac 75w90 would be idea.....Am I interpeting this correctly or will it chatter absolutely none of them additives???

tomtk

1. Do the clutches need the additives? 2. does the GM PN 1052271 and its replacement have them blended in ? he said Delvac Syn 75W90 is basically the same as the Mobil 1 75w90NS but without the any friction modifiers additives I had a 1984 2.8L V6 that I dragged all over the world while in the milit...

tomtk

Synthetic or Mineral??? Whats it say on the bottle??? Royal Purples Techline said theirs would work...but who knows the knowledge level of their techs?? Interrestingly their GL-5 is also backward compatable with GL-4 and will not harm copper alloys like most GL-5s...per them I have the rear end open...

tomtk

Is there any commercial ones thats safe to use????

tomtk

2002 G80 Axle what gear lube will work ????

What yall runnin????

tomtk

off the pump inside the module do? My original module broadcast code SGH had one but the replament number FG0070 from Delphi did not. The new module says it has improved materials for the gauge sensor and an updated wiring connector. On the Dephi site in a TSB there they show the stock wiring harnes...

tomtk

Mine is a 2002 and its steel and 17.5 gallons

I was wondering if I could convert to a larger 20 gallon pickup tank???

tomtk

Newbie to this forum. Just grabbed a 02 Crew cab with tow and zr5 in indigo blue with 72000 at $10,900. Was doing a brake job and finding what all needs to be done to make it roadworthy for me. Dex is kinda low. I plan on flushing the system and putting in the green in 2 weeks. can water be added t...

tomtk

While you have the tank off, check this line going to the rear evap vent valve (or whatever that black box is called). Mine was almost worn thru from rubbing on the cab. http://i48.photobucket.com/albums/f236/JaVeRo/100_0099.jpg This shot is from the same angle just farther back for a better locati...

tomtk

I finally tore down my truck the only trouble is the flex hose chaffed thru in module rods I have a FG0070 Mpodule on hand that Deplhi said replaced the FG0285 which was obsolete. Has a improved sender, and a larger electrical connector as they said some were melting. MY big worry is the Plastic buc...

tomtk

with this being the 3rd pump I am going to cut an access panel into the cab floor and have a friend in a Detroit sheet metal shop make me a bolt in cover for it to regain cab stiffness in the area. I will be able to fold rear seat forward and remove plate and pull module up and out quickly. Seems li...

tomtk

I will convert to MM and report back

sure would be nice to rebuild the old one and have a spare

tomtk

1.output nipple where flex hose attachs to pump 2.body diameter 3.strainer hookp diameter 4. Boby length 5. overall length I think a Delphi FE0114 will work to repair a module same pressures listed on Delphi website. Pickup tube measures the same and it has a abit more of a flow rate so it could be ...

tomtk

1.output nipple where flex hose attachs to pump 2.body diameter 3.strainer hookp diameter 4. Boby length 5. overall length I think a Delphi FE0114 will work to repair a module same pressures listed on Delphi website. Pickup tube measures the same and it has a abit more of a flow rate so it could be ...

tomtk

I have seen two diff numbers FG0248 older number and FG0070 newer number. My truck has been converted to the newer style injector head. I was considering another brand of pump as the 1st two GM parts have not lasted very long :( at least the first was under warrenty and I have changed the inline fil...

tomtk

are ya around?

Delphi lists 2 numbers FG0248 and FG0070 for the module which one is more robust? This will be 3rd pump in truck and its only at 55K

Anybody put in anaftermarket pump into the carrier with good results?

I see many Ebay repair kits and there is the possible Walbro pump

S-10CREWCAB.NET

Search found 37 matches

Does anybody know the Oring size for the radiator end of the

You guys are helpful on stuff

Re: Gotta ask about the failure rate on stock S10 Crew cabs

Gotta ask about the failure rate on stock S10 Crew cabs

I am sure it will be fine with no Oring

Typo above meant .030 smaller

Thanks Everybody Howl is gone

Steve did your Synergy Bearings have the same ...

13lb slide hammer I used

Heat wave here today 33F out so .....

Steve How fast do Justin send out orders

Any way to rig a puller to extract the hub from knuckle??

Ordered both hubs today from the above link....

So which side is most likey bad ??? I will get both BUT

OK but which side ???

Howling noise when turning right What is it ??

Ball Joints.???

I picked up that clamp from NAPA you used already...BUT

NAPA has a NEW Axle for $114

Leaking Inner drivers side CV boot.

reminds of he Harley oil selection threads

SO it sounds like

Talked with Mobil Exxon today ...so the real question is ...

SO what is the GM stuff??

Besides the GM replacement for 1052271...89021671

2002 (RPO) G80 axle what gear lube???

Fuel pump module question What does the black littlle line

DO any of the crew cab years come with a plastic gas tank

Re: FNG question

James thanx it was chaffing so.....

Help is my new FG0070 Delphi Fuel Module missing parts?????

I thought of that

Thanks

Looking for Measurements from a fuel pump inside the module

Who has an old stock pump??? I need some measurements

Thanks Henry J do ya know which Delphi Module fits?

New here 2002 that needs fuel pump...