S-10CREWCAB.NET

raven2510

The blower motor is under the hood, on the pass side of the firewall. Youll need to take out the inner fenderwell to replace it, so it takes a bit of time but not hard to do. Also there is most likely an insulation blanket in the form of a thick rubber cover over it, youll need to cut it out where ...

raven2510

The console requires the data wire and vss wire to run all the functions. It will always default to -- until you connect it.

raven2510

I would bet its his control arm bushings. Mine are doing that.

raven2510

Well you really shouldn't be able to move the belt if its tensioned right. The crank pulley has alot of compression....its hard to turn. And jumping it should at least get it started.
Do you have any power to anything? If no, you might check the mega fuse under the battery tray.

raven2510

Well do you have an aftermarket security system on the truck? That might cause it.....
The truck might be acting as an antenna for it....
And you would be surprised the power that the system puts out.

Not sure what is causing this to happen.

raven2510

It still sounds to me you need to replace the accumulator/dryer & orifice tube. Your low & high sides should be nearly equal with the engine off after like 10min. Guessing that your S10 is like 7-10 years old, I would say they are worn out/clogged. I just replaced the dryer/acc. & orifice tube on my...

raven2510

F9K9 wrote:
JORSWIFT wrote:Yea, cannot view the video as I do not have a Facebook account. Where did you put the seam foam in at?

Your engine bay is too clean. Makes mine look like crap.

raven2510

Glad you took HJ advise on it. I have seen many people put it off and pay for it later.

raven2510

If you part it out. I need the passenger side kick panel. The one on the floor by the door seal. I would also take the panels that hide the seat rails.
Do you have a Hitch?

raven2510

IAT= Intake Air Temperature

raven2510

Nope, they won't fit. They use a lip on the fenders to bolt on. They are also wider...due to the Highrider/ZR2 having 31" tires.

raven2510

Try s10Warehouse on eBay. They usually have that stuff.

raven2510

Here are some pictures of what Raptor looks like after 1.5yrs in Nebraska. I sprayed it onto my rockers & flares. I will be doing my bed this summer. http://i1187.photobucket.com/albums/z400/raven2510/1999%20Chevy%20S10%20ZR2/55ef6407.jpg http://i1187.photobucket.com/albums/z400/raven2510/1999%20Che...

raven2510

If you paint in an enclosed area without proper respiration, then yes...it can kill ya. But you can spray raptor liner outside. It has nearly no overspray because of how thick and heavy it is. I did.

raven2510

Its what I used. I will post some pics tomorrow.

raven2510

Raptor liner

raven2510

Good. Hopefully this can get a sticky.

raven2510

Yes, the pump is exposed on the extended cabs. When mine went bad I unbolted the bed, tilted in back and changed it. It took like 1hr.

raven2510

How To: S10 Hood Strut Install Ok, so after reading a thread over on S10Forum about installing gas/spring struts on the hood so that you don't have to use the prop rod, I decided it would be a neat mod to do. So here we go... Cost: $4.50 – Rivets $12+Shipping – 10mm Ball Stud brackets $25+Shipping –...

raven2510

I have never looked back after this mod. Best one so far...

raven2510

Yea, it can be done. There was a guy over at s10forum.com that changed his running DRL's to his Lower blinker lights. It was a pain IIRC

raven2510

2001 chevy blazer rear wheel bearing removal you have to drain the differential take off the cover remove pinion shaft locking bolt have it in gear than put it in neutral and turn axle til the face open is looking straight at you than remove pinion shaft than have someone push in on the axle while ...

raven2510

Itunes...its really not that expensive.

raven2510

You can mix it if you wish. But it has a lower btu total compared to reg. gasoline.
It has a higher octane due to all the alcohol...but that only makes it run cooler.
http://en.wikipedia.org/wiki/E85

If you wish to mix it...you can do like 10 gallons of reg gasoline, and 3-5 gallons of e85.

raven2510

HenryJ wrote:http://www.s-10crewcab.net/HenryJ/fans/fans.html

yep...best option. I did this exact mod to my ZR2 with the same exact parts. I have never overheated or had a problem in the last 1.5 yrs.

raven2510

Well they are powered with the rear view mirror. You could cut the wires or just remove the bulbs.

raven2510

yes, henryj is correct. You must have the ecm VIN matched to the BCM for it to work.

raven2510

I love how the storms there were national news....everyone was all freaking out. We go the same amount of snow in a weeks period a month ago and I never saw anything on the national news. No one cares about the midwest.

haha

raven2510

why not replace the seals yourself if your up to it. Its actually pretty easy...just a few bolts. I did one of mine in 2-3hrs.

raven2510

i would stay with what you use now. SYN. Oil with any name on it is protection enough for our motors. I use Mobil 1 oil and a WIX filter and have no issues...going on 5 yrs now.

raven2510

just push the panic button again

raven2510

I have to say...I love yellow s10's with the flares. Wish mine was yellow.

raven2510

are we going to be able to have quick post/response? Like the old site...if so that would be awesome.
thanks
Tad

raven2510

sorry it took so long
http://www.s10planet.com/forum/showthre ... ectric+fan

raven2510

well if they are the same as the front doors...then you could get a 1/2" spacer in there. thats what i did in my ZR2

raven2510

how much did the axle kit set you back?

raven2510

i think i have the same problem that your having.
i think my passenger side rear axle bearing is going.
i get this weird sound when turning right. its not the hubs because i just changed them both last week.

raven2510

im actually in the process of maybe getting the inside of the spokes on my zr5's coated black..

raven2510

its not from under the hood though when stock. a snorkle faces behind the headlight....and draws in air from the outside

raven2510

im about to spray my rockers and flares on my zr2 this weekend. i will post pics of the prep and the finished product.

raven2510

por 15 is a good product but it has to be top coated.

raven2510

i have the threads saved on my other computer for what you need. i will get it when i get on later tonight.

raven2510

adding an overhead console is a great mod so do on an s-series. i added mine and its got to be the best mod for the buck.

but the gas mileage is off b/c of my 31's

raven2510

what about the opposite?
mine holds fine but will not release even when i hold the handle and pull on the pedel. i have to hit it with a hammer to get it back

raven2510

the cleaner is worth it IMO. i did that and it had lots of crap in it when i used that system flush stuff.

raven2510

the Chevy/gm warranty is 8 years or 80,000 miles whichever comes first. mine cat went bad at 82,000 two yrs ago and they would not replace it. to say the least i was pissed but i understood

raven2510

mine is close...but off by 2-5*

raven2510

bad sensor.
they are cheap at the dealer. like $10-20

raven2510

welcome

raven2510

well f-body is sold out forever.

and slp needs a minimum order...so i haven't done either yet

raven2510

http://www.slponline.com/view_product.asp?P=80007
or these...
and the link i posted is for a set of 4 dude im gonna buy them right now....

raven2510

or have a decent impact wrench on hand...they work very well too

raven2510

http://www.fbodymotorsports.com/inc/sdetail/9308
are these what he has...im looking for them too

raven2510

sweet....let us know how it turns out for you.

raven2510

Here's the file from ZR2USA for you
http://www.mediafire.com/?tbk2njiwzzn

raven2510

any 98+ fuel door will work the same for you Nope. Unfortunately we have the South American Isuzu bed. It has a fender bulge over the fuel door that no other S-series shares. 2001-2004 s-series crew cab production models are the the only options. It is possible that the Isuzu Hombre may have one th...

raven2510

any 98+ fuel door will work the same for you

raven2510

i love the feel. its like i just drove it off the lot new. the steering is tight like its supposed to be.

i encourage everyone to do this. or at least change out the original ragjoint with a new one. mine was so loose that it had at least a 1/4-1/2" of play.

raven2510

where to buy http://store.summitracing.com/partdetail.asp?autofilter=1&part=FLA-FR1746DD&N=700+4294925130+4294839070+400376+4294744935+4294840405+4294848490+115&autoview=sku http://www.jegs.com/p/Flaming+River/751990/10002/-1 no increased noise or vibrations. i do mostly city and gravel roads and no...

raven2510

HOW TO: Flaming River U-Joint Steering MOD Years: 94+ S10/Blazer Time: 30min-1.5hr Cost: $70-100 Parts Needed: Flaming River U-Joint # FR1746DD Summit JEGS S-Series steering shaft (1st or 2nd Gen) LockTite Thread Locker Hacksaw or other tool to cut thin steel Dremel or Cut off-wheel 11mm socket/wren...

raven2510

might be a bad 4x4 computer? im not really sure though....or a defective motor?

raven2510

yea thanks...i found a pair in my city for $260? hopefully they are in good shape.

raven2510

how do you find sets? i only see each single?

raven2510

HenryJ wrote:You missed out by half a dozen years. Keep an eye out on ebay or check Carpart.com. They are out there for as low as $40 each now. Complete low mile A+ sets are hard to find though.

ive have looked....i have yet to see them for $40-90 apiece.

raven2510

f9k9 wrote:
Jongo8 wrote:I would love to find a set of zr5 wheels. I like them...
Would you scoop up a pristine set of four for $250?

hell f### yea i would....if they are ZR5 i would buy them NOW!!!!

raven2510

Maintaining something close to the advertised numbers for fuel mileage is going to be difficult at best. I don't know where you are from as it is not added in your profile, but if you have to use E-10 fuel like my state has mandated, be prepared to lose about 10% on your mileage. If you do 95% city...

raven2510

might be low on fluid?
can you describe the sound it makes?

raven2510

Would this system actually work :shock: Looks like another entry for the "red neck hall of fame" to me. All it needs to complete the appearance is a little baling wire. :roflmao: i totally agree. but its a proven concept. they call them rear mount turbo setups. they do have lag...but that one looks...

raven2510

no it wont fit. the blazer frame is smaller than the s10 frame.

raven2510

you shouldn't have any metal particles in your oil. that's usually a bad sign.

raven2510

they are very reliable trucks. you've replaced most of the trouble parts on the truck so i think you should be good.

raven2510

so on the HIR bulbs....are we saying that they are a good bulb to use in the high beam spot right??

raven2510

yea on the s10's they are mixed metric and standard Could you give a specific fastener that is standard? Not doubting you, I just have not come across one yet. A heep requires more freaking tools than you can imagine and I am still buying oddball tools to do simple crap to it. :x yea tell my about ...

raven2510

just did this on my zr2 and i solved my problem
i just wanted to say thanks

raven2510

yea on the s10's they are mixed metric and standard

S-10CREWCAB.NET

Search found 114 matches

Heater Squeal

overhead console w/ trip computer

what would the noise be?

Re: Dead in the water

Re: My CC sets off my dog's shock collar?!?!

Re: Air Conditioner question

Re: put seafoam in the CC today

Re: coolant leak

Re: 2002 CREW CAB For parts, everything must go. FULLY LOADE

lost compression

1999 GMC Sonoma Highrider fender flare's................

FUEL DOOR NEEDED!

Re: DIY Bed Liner

DIY Bed Liner

DIY Bed Liner

DIY Bed Liner

Re: How To: S10 Hood Strut Install

Re: How do I remove the bed on my CC?

How To: S10 Hood Strut Install

Did the throttle plate mod. today

Re: halo drl's

Re: rear wheel bearings

Re: Where do you get your music?

Re: Ethanol

Re: is there a 2003 zr5 electric fan conversion.

Re: shutting off lighted visors?

Re: ECM HELP!!! Putting in used pcm from salvage

Re: A little bit of snow

Re: Rear Axle Seals

Re: Motor oil and filter

Re: How to diasarm panic button?

Re: Horsehammerr's Ride

Re: Problems, Problems, and more problems...

HOW TO: Flaming River U-Joint Steering MOD

Re: This Turbo System?