VIBRATION WHEN BRAKING

Anything related to the stock drivetrain, engine, transmission, axles, wheels...

Moderator: F9K9

User avatar
Serge PETIT
Crew Elite
Crew Elite
Posts: 126
Joined: Sat Jan 09, 2010 3:19 pm
Location: PARIS FRANCE

VIBRATION WHEN BRAKING

Post by Serge PETIT »

Its concerning my Blazer but braking system is the same on Crew Cab and Brule authorized me to ask question about it on your forum . So I do not hesitate because of the quality of your answers !
When braking at a speed of 75 miles per hour and more (allowed speed in France ) I feel a vibration in wheels , but not a pulse in the pedal . It'smainly when outside temp is around temp is 85 °F or after half an hour on freeway .
I have made the tires balanced , brake pads have been checked and are good.
My brake liquid has been changed by a garage with DOT5 .
Any idea where it comes from ?
Your support will be appreciated because I am in France with no possible help other than garages and I have no trust in them because they will try to change all the braling system !!!!!
Thanks in advance .
Serge.
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Re: VIBRATION WHEN BRAKING

Post by HenryJ »

There can be some issues with the pad transfer to the disc being uneven. Sanding the pads and rotors to clean off any tempered or transferred material and then re-applying the bedding procedure may help.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Serge PETIT
Crew Elite
Crew Elite
Posts: 126
Joined: Sat Jan 09, 2010 3:19 pm
Location: PARIS FRANCE

Re: VIBRATION WHEN BRAKING

Post by Serge PETIT »

May it comme from the fact that the guy in charge of the maintenance of my Blazer has changed the DOT3 liquid with a DOT5 one?
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Re: VIBRATION WHEN BRAKING

Post by HenryJ »

Big OOPS! Your hydraulic braking systems are compromised. Our system is not designed to be used with silicone brake fluid (DOT5)

STOP now. Flush the entire system and refill with DOT3 or DOT4.
Maybe you will get lucky and not have to replace the calipers, master cylinder, ABS unit and brake lines.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Serge PETIT
Crew Elite
Crew Elite
Posts: 126
Joined: Sat Jan 09, 2010 3:19 pm
Location: PARIS FRANCE

Re: VIBRATION WHEN BRAKING

Post by Serge PETIT »

OK , I get in touch immediatly with my maintenance guy and change back for the DOT 3 or 4 .
Which would be the best ?
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Re: VIBRATION WHEN BRAKING

Post by HenryJ »

Brake fluid is hygroscopic. It has an affinity for water. This a a good thing as it keeps the water from damaging brake parts. Air has water. Water in the fluid lowers the boiling point and changes the hydraulic properties of the fluid.
Both will offer good firm applications until they absorb water. DOT3 has a greater affinity for water than DOT4. If your climate is moist DOT3 is the best choice. If you live in a desert DOT4 may give you better service. It has a higher boiling point and will be firm longer than DOT3. With less affinity for water it will have a longer service life.
It will be for you to decide.
DOT3 is the safe bet as it is recommended.
I use DOT4 in my high desert climate.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Serge PETIT
Crew Elite
Crew Elite
Posts: 126
Joined: Sat Jan 09, 2010 3:19 pm
Location: PARIS FRANCE

Re: VIBRATION WHEN BRAKING

Post by Serge PETIT »

I have made the contact with my maintenance guy and checked bootle and specs .
It's not a DOT5 but a DOT5.1 which is the new DOT3/DOT5 with a waranty of no silicones . The difference with the previous DOT 3 is the boiling point which is higher .
The product is based on polyoxyalkylene glycols .
I have mde the confusion with the military or racing liquid which is the DOT5 and include silicones with a violet color .
Mine is very clear "yellow" .
Now in France it's very difficult to find DOT3 and rare to find DOT4 because they are replaced with the 5.1 .
Mine is branded BENDIX Super 5 DOT5.1 and meets the SAE norm J1703 which is the DOT3 norm .

I hope that like me you will be more quiet now .................

Concerning the vibration , my external rod ties are a little bit used and it may be time to change it said my guy .
Do you think too that it may cause the vibration on "stronger" braeking due to the speed ?
Thanks for your support .
Serge;
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Re: VIBRATION WHEN BRAKING

Post by HenryJ »

European spec brake fluid causing the confusion I guess. Silicone fluid here (DOT5) is clear.

Any number of things could be the cause. Normally loose suspension components will show tire wear. Feathering, cupping, inside or outside wear.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Serge PETIT
Crew Elite
Crew Elite
Posts: 126
Joined: Sat Jan 09, 2010 3:19 pm
Location: PARIS FRANCE

Re: VIBRATION WHEN BRAKING

Post by Serge PETIT »

No tire wear ...............
Yes there is a big confusion with the number for DOT and there are a lot of claims on internet about such a possible confusion ! :mrgreen:
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Re: VIBRATION WHEN BRAKING

Post by HenryJ »

It will be a tough long distance diagnosis. There are so many variables and interpretations one can glean from this description. So much of this comes from feel and experience. Is the vibration in the wheel? That would indicate front problems. Is it in the seat? That would lean more to rear brake problems. Do you feel it in the floor? What is the sound? Deep, tinny, grinding, fast, slow? Under power? Coasting?
Did this start right after the change of fluid? Our ABS system is designed for DOT3 or DOT4 fluid. Could the European DOT5.1 be different enough to be a problem?
There are just so many things that can help get an idea what might be happening.

There are several things you can try. Sanding the pads and rotors to freshly bed the brakes is a good place to start. Inspect the slide pins to make sure that they are free. Look for signs of warping in the rotors , discoloration from hot spots and stress cracking.
Is it the ABS system activating? Pulling the fuse will disable that and rule it out.

Check for loose wheel bearings, ball joints and suspension components. Also consider the shock absorber condition. Under braking the rapid weight transfer forward might be sign they are weak.

If it has been more than 20k miles you are due for an alignment. The alignment shop can help to diagnose lots of suspension issues.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Serge PETIT
Crew Elite
Crew Elite
Posts: 126
Joined: Sat Jan 09, 2010 3:19 pm
Location: PARIS FRANCE

Re: VIBRATION WHEN BRAKING

Post by Serge PETIT »

I think we may eliminate the shocks because they are Bilstein and have around 10000 miles.
Alignment has been done at the same time .
Vibration is not in the pedal and not like ABS . There is no noise . I have the feeling that vibration is in the wheels .
What I can say is that on my previous Saab 900 Turbo S Line year 1989 , I have had the same sensation and it was the front rotors which were warped but my maintenance guy said that he has controlled and were not warped . he has controlled the pads and sanded it.
DOT5.1 is just a synthetic DOT3/4 (same as the synthetic Prestone DOT3 which is manufacture by Honeywell like mine).
Are "slide pins" the small clips delivered with the pads ?
ABS is activated in strong breaking ,I have tried .
We will check all the rest control again warping of rotors and keep you informed .
Many thanks Brule for your strong support !
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Re: VIBRATION WHEN BRAKING

Post by HenryJ »

The Raybestos brake rep has strongly emphasized the proper bedding of brakes and uneven material transfer.
Many rotors are returned under warranty due to "warping" issues when in fact they are not warped. What can happen is there is uneven material transfer. Brake pad material is transferred to the rotor. This is what helps with braking. If this material is unevenly distributed it can lead to vibration under braking. The process of sanding is not to even the surfaces. It is to scrub off that invisible layer of transferred material and break the surface hardened pad in an attempt to start fresh again. Some pads are better than others. Give them an even chance by bedding them before you put the vehicle into service.

All that said...I have run into a batch of bad rotors. They did warp and have problems due to uneven iron content. They were not suppose to be the "cheap" line , but ended up being poorly constructed. Switching to AC Delco rotors solved that problem.

If you have no success, then perhaps it is time to try some new rotors and a different brake pad.
I am very happy with the Powerslot rotors that I put on my truck. The Hawk pads were a mistake. I will likely go with OEM ceramic pads next time. I saw very good performance and life with those.

The slide pins to which I referred are the sleeves and bolts that retain the calipers. If they are not clean and lubed with brake silicone they can seize and drag a brake pad. This leads to heating one side of the rotor and pad. That can cause warping and various other problems.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
Serge PETIT
Crew Elite
Crew Elite
Posts: 126
Joined: Sat Jan 09, 2010 3:19 pm
Location: PARIS FRANCE

Re: VIBRATION WHEN BRAKING

Post by Serge PETIT »

I have the stock rotors since 10 years now and 68000miles . The pads are the AC Delco ceramic .
I use only OEM parts , I think it's the best waranty for an oversea owner !
User avatar
Serge PETIT
Crew Elite
Crew Elite
Posts: 126
Joined: Sat Jan 09, 2010 3:19 pm
Location: PARIS FRANCE

Re: VIBRATION WHEN BRAKING

Post by Serge PETIT »

User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Re: VIBRATION WHEN BRAKING

Post by HenryJ »

Good stuff.
Carroll Smith wrote:
The "Warped" Brake Disc and Other Myths of the Braking System

Myth # 1 – BRAKE JUDDER AND VIBRATION IS CAUSED BY DISCS THAT HAVE BEEN WARPED FROM EXESSIVE HEAT.


The term "warped brake disc" has been in common use in motor racing for decades. When a driver reports a vibration under hard braking, inexperienced crews, after checking for (and not finding) cracks often attribute the vibration to "warped discs". They then measure the disc thickness in various places, find significant variation and the diagnosis is cast in stone.

When disc brakes for high performance cars arrived on the scene we began to hear of "warped brake discs" on road going cars, with the same analyses and diagnoses. Typically, the discs are resurfaced to cure the problem and, equally typically, after a relatively short time the roughness or vibration comes back. Brake roughness has caused a significant number of cars to be bought back by their manufacturers under the "lemon laws". This has been going on for decades now - and, like most things that we have cast in stone, the diagnoses are wrong.

With one qualifier, presuming that the hub and wheel flange are flat and in good condition and that the wheel bolts or hat mounting hardware is in good condition, installed correctly and tightened uniformly and in the correct order to the recommended torque specification, in more than 40 years of professional racing, including the Shelby/Ford GT 40s – one of the most intense brake development program in history - I have never seen a warped brake disc. I have seen lots of cracked discs, (FIGURE 1) discs that had turned into shallow cones at operating temperature because they were mounted rigidly to their attachment bells or top hats, (FIGURE 2) a few where the friction surface had collapsed in the area between straight radial interior vanes, (FIGURE 3) and an untold number of discs with pad material unevenly deposited on the friction surfaces - sometimes visible and more often not. (FIGURE 4)

In fact every case of "warped brake disc" that I have investigated, whether on a racing car or a street car, has turned out to be friction pad material transferred unevenly to the surface of the disc. This uneven deposition results in thickness variation (TV) or run-out due to hot spotting that occurred at elevated temperatures.

In order to understand what is happening here, we will briefly investigate the nature of the stopping power of the disc brake system.
THE NATURE OF BRAKING FRICTION

Friction is the mechanism that converts dynamic energy into heat. Just as there are two sorts of friction between the tire and the road surface (mechanical gripping of road surface irregularities by the elastic tire compound and transient molecular adhesion between the rubber and the road in which rubber is transferred to the road surface), so there are two very different sorts of braking friction - abrasive friction and adherent friction. Abrasive friction involves the breaking of the crystalline bonds of both the pad material and the cast iron of the disc. The breaking of these bonds generates the heat of friction. In abrasive friction, the bonds between crystals of the pad material (and, to a lesser extent, the disc material) are permanently broken. The harder material wears the softer away (hopefully the disc wears the pad). Pads that function primarily by abrasion have a high wear rate and tend to fade at high temperatures. When these pads reach their effective temperature limit, they will transfer pad material onto the disc face in a random and uneven pattern. It is this "pick up" on the disc face that both causes the thickness variation measured by the technicians and the roughness or vibration under the brakes reported by the drivers.

With adherent friction, some of the pad material diffuses across the interface between the pad and the disc and forms a very thin, uniform layer of pad material on the surface of the disc. As the friction surfaces of both disc and pad then comprise basically the same material, material can now cross the interface in both directions and the bonds break and reform. In fact, with adherent friction between pad and disc, the bonds between pad material and the deposits on the disc are transient in nature - they are continually being broken and some of them are continually reforming.

There is no such thing as pure abrasive or pure adherent friction in braking. With many contemporary pad formulas, the pad material must be abrasive enough to keep the disc surface smooth and clean. As the material can cross the interface, the layer on the disc is constantly renewed and kept uniform - again until the temperature limit of the pad has been exceeded or if the pad and the disc have not been bedded-in completely or properly. In the latter case, if a uniform layer of pad material transferred onto the disc face has not been established during bedding or break-in, spot or uncontrolled transfer of the material can occur when operating at high temperatures. The organic and semi-metallic pads of the past were more abrasive than adherent and were severely temperature limited. All of the current generation of "metallic carbon", racing pads utilize mainly adherent technology as do many of the high end street car pads and they are temperature stable over a much higher range. Unfortunately, there is no free lunch and the ultra high temperature racing pads are ineffective at the low temperatures typically experienced in street use.

Therefore - there is no such thing as an ideal "all around" brake pad. The friction material that is quiet and functions well at relatively low temperatures around town will not stop the car that is driven hard. If you attempt to drive many cars hard with the OEM pads, you will experience pad fade, friction material transfer and fluid boiling - end of discussion. The true racing pad, used under normal conditions will be noisy and will not work well at low temperatures around town.

Ideally, in order to avoid either putting up with squealing brakes that will not stop the car well around town or with pad fade on the track or coming down the mountain at speed, we should change pads before indulging in vigorous automotive exercise. No one does. The question remains, what pads should be used in high performance street cars - relatively low temperature street pads or high temperature race pads? Strangely enough, in my opinion, the answer is a high performance street pad with good low temperature characteristics. The reason is simple: If we are driving really hard and begin to run into trouble, either with pad fade or boiling fluid (or both), the condition(s) comes on gradually enough to allow us to simply modify our driving style to compensate. On the other hand, should an emergency occur when the brakes are

cold, the high temperature pad is simply not going to stop the car. As an example, during the mid 1960s, those of us at Shelby American did not drive GT 350 or GT 500 Mustangs as company cars simply because they were equipped with Raybestos M-19 racing pads and none of our wives could push on the brake pedal hard enough to stop the car in normal driving.

Regardless of pad composition, if both disc and pad are not properly broken in, material transfer between the two materials can take place in a random fashion - resulting is uneven deposits and vibration under braking. Similarly, even if the brakes are properly broken, if, when they are very hot or following a single long stop from high speed, the brakes are kept applied after the vehicle comes to a complete stop it is possible to leave a telltale deposit behind that looks like the outline of a pad. This kind of deposit is called pad imprinting and looks like the pad was inked for printing like a stamp and then set on the disc face. It is possible to see the perfect outline of the pad on the disc. (FIGURE 5)

It gets worse. Cast iron is an alloy of iron and silicon in solution interspersed with particles of carbon. At elevated temperatures, inclusions of carbides begin to form in the matrix. In the case of the brake disk, any uneven deposits - standing proud of the disc surface - become hotter than the surrounding metal. Every time that the leading edge of one of the deposits rotates into contact with the pad, the local temperature increases. When this local temperature reaches around 1200 or 1300 degrees F. the cast iron under the deposit begins to transform into cementite (an iron carbide in which three atoms of iron combine with one atom of carbon). Cementite is very hard, very abrasive and is a poor heat sink. If severe use continues the system will enter a self-defeating spiral - the amount and depth of the cementite increases with increasing temperature and so does the brake roughness. Drat!
PREVENTION

There is only one way to prevent this sort of thing - following proper break in procedures for both pad and disc and use the correct pad for your driving style and conditions. All high performance after market discs and pads should come with both installation and break in instructions. The procedures are very similar between manufacturers. With respect to the pads, the bonding resins must be burned off relatively slowly to avoid both fade and uneven deposits. The procedure is several stops of increasing severity with a brief cooling period between them. After the last stop, the system should be allowed to cool to ambient temperature. Typically, a series of ten increasingly hard stops from 60mph to 5 mph with normal acceleration in between should get the job done for a high performance street pad. During pad or disc break-in, do not come to a complete stop, so plan where and when you do this procedure with care and concern for yourself and the safety of others. If you come to a complete stop before the break-in process is completed there is the chance for non-uniform pad material transfer or pad imprinting to take place and the results will be what the whole process is trying to avoid. Game over.

In terms of stop severity, an ABS active stop would typically be around 0.9 G’s and above, depending on the vehicle. What you want to do is stop at a rate around 0.7

to 0.9 G's. That is a deceleration rate near but below lock up or ABS intervention. You should begin to smell pads at the 5th to 7th stop and the smell should diminish before the last stop. A powdery gray area will become visible on the edge of the pad (actually the edge of the friction material in contact with the disc - not the backing plate) where the paint and resins of the pad are burning off. When the gray area on the edges of the pads are about 1/8" deep, the pad is bedded.

For a race pad, typically four 80mph to 5 and two 100mph to 5, depending on the pad, will also be necessary to raise the system temperatures during break-in to the range that the pad material was designed to operate at. Hence, the higher temperature material can establish its layer completely and uniformly on the disc surface.

Fortunately the procedure is also good for the discs and will relieve any residual thermal stresses left over from the casting process (all discs should be thermally stress relieved as one of the last manufacturing processes) and will transfer the smooth layer of pad material onto the disc. If possible, new discs should be bedded with used pads of the same compound that will be used going forward. Again, heat should be put into the system gradually - increasingly hard stops with cool off time in between. Part of the idea is to avoid prolonged contact between pad and disc. With abrasive pads (which should not be used on high performance cars) the disc can be considered bedded when the friction surfaces have attained an even blue color. With the carbon metallic type pads, bedding is complete when the friction surfaces of the disc are a consistent gray or black. In any case, the discoloration of a completely broken in disc will be complete and uniform.

Depending upon the friction compound, easy use of the brakes for an extended period may lead to the removal of the transfer layer on the discs by the abrasive action of the pads. When we are going to exercise a car that has seen easy brake use for a while, a partial re-bedding process will prevent uneven pick up.

The driver can feel a 0.0004" deposit or TV on the disc. 0.001" is annoying. More than that becomes a real pain. When deposit are present, by having isolated regions that are proud of the surface and running much hotter than their neighbors, cementite inevitably forms and the local wear characteristics change which results in ever increasing TV and roughness.

Other than proper break in, as mentioned above, never leave your foot on the brake pedal after you have used the brakes hard. This is not usually a problem on public roads simply because, under normal conditions, the brakes have time to cool before you bring the car to a stop (unless, like me, you live at the bottom of a long steep hill). In any kind of racing, including autocross and "driving days" it is crucial. Regardless of friction material, clamping the pads to a hot stationary disc will result in material transfer and discernible "brake roughness". What is worse, the pad will leave the telltale imprint or outline on the disc and your sin will be visible to all and sundry.

The obvious question now is "is there a "cure" for discs with uneven friction material deposits?" The answer is a conditional yes. If the vibration has just started, the chances are that the temperature has never reached the point where cementite begins to form. In this case, simply fitting a set of good "semi-metallic" pads and using them hard (after bedding) may well remove the deposits and restore the system to normal operation but with upgraded pads. If only a small amount of material has been transferred i.e. if the vibration is just starting, vigorous scrubbing with garnet paper may remove the deposit. As many deposits are not visible, scrub the entire friction surfaces thoroughly. Do not use regular sand paper or emery cloth as the aluminum oxide abrasive material will permeate the cast iron surface and make the condition worse. Do not bead blast or sand blast the discs for the same reason.

The only fix for extensive uneven deposits involves dismounting the discs and having them Blanchard ground - not expensive, but inconvenient at best. A newly ground disc will require the same sort of bedding in process as a new disc. The trouble with this procedure is that if the grinding does not remove all of the cementite inclusions, as the disc wears the hard cementite will stand proud of the relatively soft disc and the thermal spiral starts over again. Unfortunately, the cementite is invisible to the naked eye.

Taking time to properly bed your braking system pays big dividends but, as with most sins, a repeat of the behavior that caused the trouble will bring it right back.

MYTH # 2 - RACING BRAKE DISCS ARE MADE FROM STEEL

To digress for a moment "steel discs" are a misnomer frequently used by people who should know better. This group includes TV commentators and drivers being interviewed. Except for some motorcycles and karts, all ferrous discs are made from cast iron - an excellent material for the job. While steel has a higher tensile strength, cast iron is many times stronger than disc brake requirements. Its thermal transfer characteristics are significantly better than those of steel so that the heat generated at the interface between pad and disc is efficiently carried through the friction faces to the interior surface of the disc and into the vanes from where the heat is dissipated into the air stream. Cast iron is more dimensionally stable at elevated temperature than steel and is a better heat sink - so let us hear no more talk of "steel" brake discs.
MYTH # 3 - A SOFT BRAKE PEDAL IS THE RESULT OF PAD FADE

The all too familiar mushy brake pedal is caused by overheated brake fluid, not overheated pads. Repeated heavy use of the brakes may lead to "brake fade". There are two distinct varieties of brake fade

A) When the temperature at the interface between the pad and the rotor exceeds the thermal capacity of the pad, the pad loses friction capability due largely to out gassing of the binding agents in the pad compound. The brake pedal remains firm and solid but the car will not stop. The first indication is a distinctive and unpleasant smell which should serve as a warning to back off,

B) When the fluid boils in the calipers air bubbles are formed. Since air is compressible, the brake pedal becomes soft and "mushy" and pedal travel increases. You can probably still stop the car by pumping the pedal but efficient modulation is gone. This is a gradual process with lots of warning.
MYTH # 4 - BOILED BRAKE FLUID WILL BE SERVICABLE AFTER IT COOLS.

Once the brake fluid inside the caliper has boiled, it has lost a significant percentage of its original boiling point and should be replaced. It is not necessary to remove all of the fluid in the system, just bleed until clear fluid appears.
MYTH # 5 - BECAUSE THEY ARE NON-HYGROSCOPIC SILICON BASED BRAKE FLUIDS ARE SUITABLE FOR USE IN HIGH PERFORMANCE CARS

DOT 3 AND DOT 4 brake fluids are ether based and are hygroscopic in nature - i.e. they absorb water vapor. As the braking system in not quite airtight, a significant amount of water can be absorbed from the atmosphere in the course of a year. A 3% water content in brake fluid drops the boiling point as much as 170 degrees F. Brake fluid should be completely replaced annually.
DOT 5 fluids are silicon based and are non-hygroscopic, which is good. They are also subject to frothing from high frequency vibration, which gives a soft pedal. Soft brake pedals may be OK in non-high performance cars (in fact, most drivers accept mushy brake pedals as normal) but they are not acceptable in any situation where the driver intends to modulate braking at high force values.
MYTH # 6 - The brake fluid reservoir should be topped up during routine service.

In most modern passenger cars, the brake fluid reservoir is designed with a specific volume and is equipped with an internal float. The volume corresponds to the amount of fluid that will be displaced when the pads have worn to the point of replacement plus a generous reserve. When the replacement point is reached, the descending float completes an electrical circuit and a light appears on the dash warning the driver that the pads should be replaced.
If the brake fluid is topped up the first warning of warn out pads will be the screech of steel backing plate against iron disc. This will be both annoying and expensive.

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
roadrunner
Crew K Elite
Crew K Elite
Posts: 1267
Joined: Wed Dec 05, 2007 5:39 pm
Location: NW KS

Re: VIBRATION WHEN BRAKING

Post by roadrunner »

Interesting and all well and good but I do believe you'd be hard pressed to prove that all the cars turned out at the assembly plants get this type of break-in and having worked in a dealership I can personally attest it is NOT part of the pre-delivery schedule. Or are the manufacturers claiming new pads are that much better/worse this procedure is required. If that's the case then the OEM pad is better argument comes under suspicion as well. JMO
2001 CC LS, pewter, stock, 4.3,Wait4meperformance, CFM throttle blade, Helix throttle body spacer, 4spd auto, 3button electric 4x4 shift, heavy duty factory suspension, Bilsteins, 1" rear wheel spacers, skid plates.
SleeperSS
Enthusiast
Enthusiast
Posts: 29
Joined: Fri Oct 30, 2009 5:38 am

Re: VIBRATION WHEN BRAKING

Post by SleeperSS »

Something to consider that's not related to the brakes...bad ball joints will cause a bad vibration/shaking when slowing...especially on turns.
User avatar
F9K9
Mod K Elite
Mod K Elite
Posts: 6183
Joined: Sun May 30, 2004 12:26 pm
Location: London, Kentucky, United States

Re: VIBRATION WHEN BRAKING

Post by F9K9 »

Image
[size=75][b]"For those who have fought for it, [i][color=red]FR[/color][color=white]EE[/color][color=blue]DOM[/color][/i] has a taste that the protected will never know."
[url=http://www.naxja.org/forum/showthread.php?t=73349]GUIDE TO SEARCHING. [i] (Some of the forum software is different but, it has helped me a lot.)[/i][/url][/b]
[b]"Those who don't know history are destined to repeat it." Edmund Burke[/b][/size]
User avatar
roadrunner
Crew K Elite
Crew K Elite
Posts: 1267
Joined: Wed Dec 05, 2007 5:39 pm
Location: NW KS

Re: VIBRATION WHEN BRAKING

Post by roadrunner »

Dude! You're facing away from the screen in the pic!
2001 CC LS, pewter, stock, 4.3,Wait4meperformance, CFM throttle blade, Helix throttle body spacer, 4spd auto, 3button electric 4x4 shift, heavy duty factory suspension, Bilsteins, 1" rear wheel spacers, skid plates.
User avatar
HenryJ
Admin K Elite
Admin K Elite
Posts: 12705
Joined: Tue Oct 01, 2002 9:14 pm
Location: Ontario, Oregon
Contact:

Re: VIBRATION WHEN BRAKING

Post by HenryJ »

roadrunner wrote:Dude! You're facing away from the screen in the pic!
Alzheimer's rearing its ugly head? :lol: Jeez Reed! This last year really has aged you ;)

"Speed doesn't kill, suddenly becoming stationary does." - Richard Hammond
"Speed is just a matter of Money - How fast do YOU want to go?"-Mechanic from Mad Max-
If at first you don't succeed - Don't take up Skydiving!
- ThunderII KE7CSK
User avatar
F9K9
Mod K Elite
Mod K Elite
Posts: 6183
Joined: Sun May 30, 2004 12:26 pm
Location: London, Kentucky, United States

Re: VIBRATION WHEN BRAKING

Post by F9K9 »

HenryJ wrote:............Jeez Reed! This last year really has aged you ;)
Tell me something I know know! :roflmao:
[size=75][b]"For those who have fought for it, [i][color=red]FR[/color][color=white]EE[/color][color=blue]DOM[/color][/i] has a taste that the protected will never know."
[url=http://www.naxja.org/forum/showthread.php?t=73349]GUIDE TO SEARCHING. [i] (Some of the forum software is different but, it has helped me a lot.)[/i][/url][/b]
[b]"Those who don't know history are destined to repeat it." Edmund Burke[/b][/size]
User avatar
rlrnr53
Crew Elite
Crew Elite
Posts: 557
Joined: Wed Dec 28, 2005 2:04 pm
Location: Prosperty, West Virginia

Re: VIBRATION WHEN BRAKING

Post by rlrnr53 »

Reed, we don't get older, we just mellow with age!
[size=75]Mitch
2001 Polo Green Metallic, no mods,(can't afford any)[/size]
User avatar
z28
Enthusiast
Enthusiast
Posts: 40
Joined: Tue Oct 26, 2010 6:52 pm
Location: Central Kansas

Re: VIBRATION WHEN BRAKING

Post by z28 »

i have a 2003 ZR5. I have recently noticed a vibration in my brakes as well. I feel it through the pedal. No one else in the truck can feel it. It had new pads and an ABS controler maybe 5000 miles ago. Could this be warped rotors as you have been talking about or could it be something ABS related. This is the first vehicle i have ever owned with antilocks. Just looking for some greater knowledge before I go tearing into it. Thanks
2003 S10 Crew Cab ZR5
User avatar
z28
Enthusiast
Enthusiast
Posts: 40
Joined: Tue Oct 26, 2010 6:52 pm
Location: Central Kansas

Re: VIBRATION WHEN BRAKING

Post by z28 »

forgot to mention it I only feel the vibration at moderate to hard braking. I hardly ever feel it just driving around town at low speeds. Thats what makes me think its in the ABS.
2003 S10 Crew Cab ZR5
User avatar
Serge PETIT
Crew Elite
Crew Elite
Posts: 126
Joined: Sat Jan 09, 2010 3:19 pm
Location: PARIS FRANCE

Re: VIBRATION WHEN BRAKING

Post by Serge PETIT »

I just realize that I have not given any update ................ :twisted:

Sympoms were the same. The brake pedal was not directly vibrating but I was feeling the vibration in the whole front of the car and it was always at a speed over 110 km/h.

We have first controled the balance of tires , wheel bearings ... all was good
After we have change the tie rods and at the same time taken the opportunity for changing the stabilizer bar bushings and links with the Energy suspension ones (realy a must have)..........Vibration was always there .
So we have taken the décision to change the rotors and pads with OE ones (AC Delco) and the vibration stopped imediatly . Problem was solved .

Trying to understand why the wrapping , considering that the rotors were having only 110000 km , I have remembered that , the vibration has started after the fact that , the rotors behing very hot due to a highway very intense trafic with many braking and a sudden big storm so I have been driving in big pool of water . So , I do think that the wrapping was coming from there after the thermic shock .
Hope it may help .
8)
User avatar
F9K9
Mod K Elite
Mod K Elite
Posts: 6183
Joined: Sun May 30, 2004 12:26 pm
Location: London, Kentucky, United States

Re: VIBRATION WHEN BRAKING

Post by F9K9 »

Thanks for following up on your situation.
[size=75][b]"For those who have fought for it, [i][color=red]FR[/color][color=white]EE[/color][color=blue]DOM[/color][/i] has a taste that the protected will never know."
[url=http://www.naxja.org/forum/showthread.php?t=73349]GUIDE TO SEARCHING. [i] (Some of the forum software is different but, it has helped me a lot.)[/i][/url][/b]
[b]"Those who don't know history are destined to repeat it." Edmund Burke[/b][/size]