Search found 851 matches
- Mon Aug 22, 2016 7:22 am
- Forum: Tires / Lifts / Suspension
- Topic: Zr5 prerunner
- Replies: 4
- Views: 1936
You would probably need to do a 2 piece driveshaft. The stock rear shaft is already ridiculously long. If memory is correct, the place that built my driveshafts after my axle swap said that they won't build any driveshafts with more than 4 foot of tube, and mine was very close. I believe the extende...
- Thu Aug 11, 2016 4:48 am
- Forum: Stock Mechanical / Drivetrain
- Topic: ABS Control Module
- Replies: 4
- Views: 1508
- Mon Aug 08, 2016 6:59 pm
- Forum: Stock Mechanical / Drivetrain
- Topic: ABS Control Module
- Replies: 4
- Views: 1508
- Sun Aug 07, 2016 9:27 am
- Forum: Crew Cab Modifications
- Topic: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
- Replies: 45
- Views: 6285
http://www.pirate4x4.com/forum/chevy/2220121-_stuckys-junk.html#/enter Don't think too much about the quick ratio steering box. I tried a few different boxes and ended up building my own. I used a stock s10 case and put around 99 Chevy express van guts in it. One problem I had with the Astro box is ...
- Fri Aug 05, 2016 8:08 am
- Forum: Crew Cab Modifications
- Topic: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
- Replies: 45
- Views: 6285
Dang, for 250 I'd drag the whole thing home. You can't use the steering box on an s10, the mounts are different. But waggy boxes are somewhat desirable if it has a "76" stamped on it. They have some beefier internals. I don't know what all they fit. Also you might check if it has a Dana 44 or an amc...
- Sun Jul 31, 2016 7:51 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
This setup has a 50 amp fuse, 3 automotive relays, then the ground goes through the switch I have in the cab. The relays are supposed to be wired in a way that when the high circuit gets power it cuts the low circuit. I just have the 1 circuit wired, the 2nd circuit has the trigger wire wrapped up a...
- Sat Jul 30, 2016 6:19 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
So I had it all planned out. I drew up a diagram to copy the relay setup to show you guys. About drove my self nuts trying to think of how I messed it up. I spent a large part of today on Google. Well, I finally went up there and was looking everything over. Turns out the fan I got from the junkyard...
- Sat Jul 30, 2016 7:55 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
Hey brule and Anthony, I think I need help with some wiring. Or at least just a double check. So the Yj. I had bought a used hollister road relay setup from a guy on pirate. When I got it you could see where the plastic blocks that hold the relays had been hot, this may be where the issue is, not su...
- Wed Jul 27, 2016 5:52 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
- Wed Jul 27, 2016 6:53 am
- Forum: Electrical Modifications / Audio / Video / Lighting
- Topic: Rockford Fosgate R2S-1X10 Prime R2S Single 10-Inch Shallow L
- Replies: 9
- Views: 2354
Hahaha. Yea the bazooka is more to kinda round out the sound range, probably not going to be knocking any mirrors off the windshield. It's been a while since I was looking for panty droppin' bass, and honestly it probably didn't work then anyways. But the back seat on these isn't really set up for w...
- Mon Jul 25, 2016 7:33 am
- Forum: Electrical Modifications / Audio / Video / Lighting
- Topic: Rockford Fosgate R2S-1X10 Prime R2S Single 10-Inch Shallow L
- Replies: 9
- Views: 2354
Several of the members here have used an amplified bazooka bass tube. That's what I put in mine a few years back, but I had some feedback issues I never figured out and ended up unhooking it. Building a box has been on the to do list for a long time, but I don't know if I ever will. Let us know how ...
- Thu Jul 21, 2016 7:58 am
- Forum: Stock Crew Cab
- Topic: Towing my ZR5
- Replies: 1
- Views: 1460
- Fri Jul 15, 2016 7:53 am
- Forum: Crew Cab Modifications
- Topic: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
- Replies: 45
- Views: 6285
Ok so that 90 k5 has 10 bolts front and rear, they are not desirable. I wouldn't even consider using the rear 10 bolt, but if you have a semi float 14 bolt from the heavy half tons, it's a reasonable combo. That's what I ran in my k5 for a few years. Granted I ended up with chromoly shafts in the fr...
- Thu Jul 07, 2016 4:10 pm
- Forum: Crew Cab Modifications
- Topic: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
- Replies: 45
- Views: 6285
Re: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
I'm sure you probably could but personally I would (and did) eliminate that too.
- Thu Jul 07, 2016 6:59 am
- Forum: Crew Cab Modifications
- Topic: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
- Replies: 45
- Views: 6285
- Mon Jul 04, 2016 9:36 am
- Forum: Crew Cab Modifications
- Topic: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
- Replies: 45
- Views: 6285
- Mon Jul 04, 2016 6:06 am
- Forum: Crew Cab Modifications
- Topic: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
- Replies: 45
- Views: 6285
- Sun Jul 03, 2016 4:20 am
- Forum: Crew Cab Modifications
- Topic: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
- Replies: 45
- Views: 6285
Ok so to make the 241 work, with the bravada shaft, it's just a matter of putting it in gear, that's all. If you use the 233, with the bravada shaft, you are eliminating the vacuum actuator on the axle along with the issues that come with it. I never had a problem but the vacuum switch on the top of...
- Sat Jul 02, 2016 1:12 pm
- Forum: Crew Cab Modifications
- Topic: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
- Replies: 45
- Views: 6285
- Sat Jul 02, 2016 8:14 am
- Forum: Crew Cab Modifications
- Topic: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
- Replies: 45
- Views: 6285
On the fan, 99ish intrepid. I'm not sure if polarity can be reversed, I mean probably if you are smart enough but it'd be easier to just put a pusher in front. Haha yea no limp mode with a manual. Slipped my mind. I hear you on manual everything. On my crew when I did the axle swap, I really wanted ...
- Thu Jun 30, 2016 7:25 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
For the last few months, as time and money allows, I've been tinkering on the yj. I currently have a "clampy" inspired build going, YouTube "Toyota clampy" if you don't know what I mean. So currently, 95 yj, 2.5/ax5/241d/drw gm60/d70hd. My brother had some 38s on 20s that I put on to roll around. I ...
- Thu Jun 30, 2016 6:49 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: Anyone interested in Firearms and/or Edged Weapons?
- Replies: 242
- Views: 152271
- Thu Jun 30, 2016 6:47 am
- Forum: Crew Cab Modifications
- Topic: 2002 4wd crewcab Sonoma vortec 5.7 and nv3500 swap
- Replies: 45
- Views: 6285
As for the tcase, mind you I haven't done this, just read about from the solid axle guys, but some people swap over to a manual shift 231 or 241 and they have to ground a connector (I'm not sure what or where) that tells the truck it's in low range. If you don't do that the trans can go into limp mo...
- Tue Jun 28, 2016 7:27 pm
- Forum: Crew Cab Modifications
- Topic: 2000 4.3 PCV Oil Catch Can Setup
- Replies: 1
- Views: 1355
Maybe something like this could work:
http://www.pirate4x4.com/forum/general- ... tml#/enter
On a side note, liven it up around here. Let's see what you guys are doing
http://www.pirate4x4.com/forum/general- ... tml#/enter
On a side note, liven it up around here. Let's see what you guys are doing
- Tue Jun 28, 2016 6:02 am
- Forum: Crew Cab Modifications
- Topic: replacement catalytic converter
- Replies: 4
- Views: 1605
- Thu Jun 23, 2016 11:06 am
- Forum: Classifieds
- Topic: WTB: crew topper
- Replies: 4
- Views: 1906
WTB: crew topper
Had a mishap with my bed topper and wanting to find another. Black preferably. Within a driving distance. I'm in central IL, around Springfield.
- Thu Jun 23, 2016 11:02 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
So after that last post, I had a bit of carnage. I swapped all those ends for the steering, had it aligned, everything was nice.... Until I slid into a ditch and bent the frame. Had it pulled out at a body shop, and it seems fine but I feel I can't trust it. Anywho, the reason for this post is I had...
- Thu Jun 16, 2016 5:50 am
- Forum: Tires / Lifts / Suspension
- Topic: Measurements for Boise Springworks Kit?
- Replies: 6
- Views: 2662
- Thu May 19, 2016 5:11 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: DOB
- Replies: 2
- Views: 2369
- Tue Apr 19, 2016 4:38 am
- Forum: Tires / Lifts / Suspension
- Topic: Measurements for Boise Springworks Kit?
- Replies: 6
- Views: 2662
- Sun Apr 03, 2016 6:34 am
- Forum: Crew Cab Modifications
- Topic: Radiator upgrade
- Replies: 62
- Views: 15248
- Fri Jan 22, 2016 6:55 am
- Forum: Stock Electrical / Audio / Lighting
- Topic: CHMSL Asmbly. removal
- Replies: 4
- Views: 1596
- Wed Jan 06, 2016 9:09 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
It's been slow around here so here's an update. Nothing major. Yet. So my steering had been feeling a little loose. Started looking and noticed that the draglink end that goes into the pass side tierod wasn't fully seated, which kinda egged out the hole and scarred up the stud. Replaced all 4 ends a...
- Sat Dec 05, 2015 4:12 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
http://i1067.photobucket.com/albums/u422/_STUCKY/zr5/B206A2D2-E5A3-468D-8EDF-8EAD6AC022F6.jpg Newest addition is the blazer roof rack on the top. Here's the new leafs vs old leaves. Shackle angle was the goal. Old on top. http://i1067.photobucket.com/albums/u422/_STUCKY/zr5/B2CDD476-182A-4EB2-8112-...
- Tue Dec 01, 2015 6:47 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
Yea my mechanic buddy agreed, change it while I'm there. I've got a hard start issue, he said that *could be it. We have been suspecting the fuel pump, hopefully it was the regulator. Fuel pressure regulator is a pricey little booger, Napa charged me like 63$. I've got it mostly back together. Distr...
- Mon Nov 30, 2015 6:18 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
- Sun Nov 29, 2015 5:59 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
So I'm down to the distributor and the intake manifold. What all should I replace while I'm this deep? I don't think it has been this far apart yet (approx. 105,000 miles currently). I am thinking intake manifold, water pump, and valve cover gaskets, rotor for the distributor, and possibly a new wat...
- Thu Nov 26, 2015 5:29 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
- Thu Nov 26, 2015 3:01 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
So the truck got new main leafs in the front this week. I had a shop make some 2 inches longer on long side, center pin forward 1/8 inch and 1/2 inch more arch. They are in and shackle angle is much better and ride is much better, I'm happy. Last night I swapped in efans. Now I have an antifreeze le...
- Sat Nov 14, 2015 5:17 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
So I plan to use a drw 60/70 for my next project. Ive been trying to sell some parts to make way for new parts. So my buddy had a guy come up today to buy my artec trussed 4.10 geared exploder 8.8 setup sua for a Yj. I didn't want to leave it sitting in the dirt so I planned to swap the 70 in. Take ...
- Mon Nov 09, 2015 8:03 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
I was really hoping to give another update with pics but I have an order from ruffstuff that's back ordered and have no idea when it'll get shipped out. I'm not really in a hurry though so it's all good. Ordered disk brake brackets for the Dana 70 (3.25 inch weld on brackets), top plates for the Dan...
- Mon Nov 09, 2015 7:56 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: Avalanche help!
- Replies: 293
- Views: 208139
- Fri Oct 30, 2015 7:19 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
Made a little progress. The brake kit came for the d60 yesterday so I put it on. I wasn't sure if it would work with the dually hubs, which use bolts instead of studs to hold it together. Perfect fit though, I'm happy. http://i1067.photobucket.com/albums/u422/_STUCKY/other%20stuff/2F2ED976-05F6-4C70...
- Mon Oct 26, 2015 12:05 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
I've been trying to round up all my parts that I plan to use that I already have. I have the axles pulled and cleaned and at my house. I ordered front brakes from lugnut4x4 , going to go 3/4 brakes up front. I actually can't replace the stock stuff or just order his brackets and get the rest locally...
- Wed Oct 21, 2015 5:27 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
No I havent really looked into them. The 2 options Ive been thinking about is sending the computer to get tuned and the harness trimmed down by this guy: http://www.pirate4x4.com/forum/motor-tranny-t-case-performance/924402-gm-pcm-tunes-150-life.html Or figure out how to trim it down myself, which I...
- Mon Oct 19, 2015 6:54 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
Here's what I plan to do with the 4l60e: http://www.pirate4x4.com/forum/chevy/1896074-4l60e-4l80e-manual-shift-control.html And a more ghetto fab version: http://youtu.be/ozbWf_QsPrw I don't fully understand yet, but am very willing to learn. I would like the transmission to shift in this pattern: p...
- Sun Oct 18, 2015 6:12 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
Hey guys. I don't know if anyone is still paying attention but I'll update anyways.... S10 is working fine. I have some parts on the kitchen counter that I hope will get the steering fixed (ie turn lock to lock). I plan to get some longer spring packs built for the front this winter to hopefully get...
- Mon Sep 28, 2015 2:43 pm
- Forum: Crew Cab Modifications
- Topic: Radiator upgrade
- Replies: 62
- Views: 15248
- Mon Sep 28, 2015 4:57 am
- Forum: Crew Cab Modifications
- Topic: Radiator upgrade
- Replies: 62
- Views: 15248
- Tue Sep 08, 2015 10:41 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
Well... No dice... The guy I talked to said that the longest they can ream it with the taper I need for my draglink end is 6.75 inch. The same as my waggy pitman arm. So no gain. He also told me you want it at 90% and I should be getting all I can out of what I have. He said about the only thing I c...
- Mon Sep 07, 2015 4:50 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
I have been really wanting a longer pitman arm. But.... I procrastinate..... I intended to call partsmike last week about this: http://www.partsmike.com/index.php?crn=204&rn=1630&action=show_detail But.... I didn't.... So I got out the tape measure today. My knuckles are ~7.5 in. center to center (b...
- Mon Sep 07, 2015 5:52 am
- Forum: Stock Mechanical / Drivetrain
- Topic: How to do Brakes
- Replies: 50
- Views: 9402
- Tue Aug 25, 2015 9:43 am
- Forum: Crew Cab Modifications
- Topic: My 2003 CC
- Replies: 37
- Views: 7048
- Thu Aug 13, 2015 8:33 am
- Forum: Stock Crew Cab
- Topic: Cab mounts on frame starting to rust
- Replies: 7
- Views: 2453
- Tue Aug 04, 2015 10:38 am
- Forum: Classifieds
- Topic: Crew cab 6ft bed v8 craigslist find
- Replies: 14
- Views: 3796
- Tue Aug 04, 2015 10:35 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
- Mon Jul 20, 2015 11:35 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
My buddy with the xj is trying to get a group of Midwest wheelers to meet up at The Badlands in Attica Indiana for Labor Day weekend (sept 4-7 weekend). I encourage anyone and everyone to come. Bring your 4wheeler, your wife's SUV, your moms van, hell I don't care. They have a nice family friendly c...
- Sun Jul 19, 2015 9:41 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
It was the rock ledge that got into the door. So yesterday me and my buddy with the xj went to the local mud park. Watching the idiots and the circus is worth the price of admission. They don't have a lot that I enjoy, but they are close to home. We always seem to end up playing on the chunks of con...
- Fri Jul 17, 2015 8:55 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
Alright, I'll fill you guys in on recent changes. So I took the off rear flares a couple weeks back. They were falling off. I broke like 8 of 10 of the studs getting them off and had to use a grinder to get the broken junk out, which I got into the paint a bit. The flare less look is growing on me. ...
- Thu Jul 16, 2015 4:00 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
- Thu Jul 16, 2015 3:59 pm
- Forum: Stock Crew Cab
- Topic: Door Hinge Pin Bushings
- Replies: 11
- Views: 4182
- Tue Jul 07, 2015 9:09 am
- Forum: Tires / Lifts / Suspension
- Topic: Moog LCA sway bar link mount
- Replies: 6
- Views: 1863
- Sat Jul 04, 2015 1:37 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: Happy Fourth
- Replies: 4
- Views: 1965
- Sat Jul 04, 2015 9:01 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: Happy Fourth
- Replies: 4
- Views: 1965
Re: Happy Fourth
Happy 4th!
Let's see how many pics we get of crew s10s (and avalanches ) in front of flags! I'll get one today!
Let's see how many pics we get of crew s10s (and avalanches ) in front of flags! I'll get one today!
- Fri Jul 03, 2015 7:59 am
- Forum: Stock Mechanical / Drivetrain
- Topic: Evap System/Fuel Tank Question
- Replies: 8
- Views: 2354
- Tue Jun 30, 2015 11:37 am
- Forum: Stock Crew Cab
- Topic: RPO U8555, in a spray can?
- Replies: 2
- Views: 1898
RPO U8555, in a spray can?
I removed my rear flares. I'm not happy with what was underneath. Can I get my paint code in a spray can? Truck is black, u8555. I'm not having any luck finding anything and I'm too cheap to pay a body shop to do it. Or maybe I ran out of dollars on the axle swap, either way, I need to do something....
- Thu Jun 25, 2015 7:54 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
At some point I would like to build some, but honestly my welding skills are very lacking. I have to rely on other people when I need welding. But I do have a buddy with a bender, it's just hard to get him to work on anything that's not his. What I'd really like to do instead of sliders, is kinda li...
- Tue Jun 16, 2015 2:19 pm
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: What did you do to your Crew today?
- Replies: 367
- Views: 193172
- Tue Jun 16, 2015 10:22 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
- Tue Jun 16, 2015 10:14 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
- Tue Jun 16, 2015 10:07 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: _STUCKY's junk
- Replies: 432
- Views: 243229
Here's some more pics. Any questions, just ask :wave: In no particular order, some from Attica, some from local mud park, some of new things... http://i1067.photobucket.com/albums/u422/_STUCKY/zr5/DDE9EDAE-B5A8-4E14-A4B2-3CD2E06C53EA.jpg http://i1067.photobucket.com/albums/u422/_STUCKY/zr5/D10C4FE8-...
- Tue Jun 16, 2015 9:39 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: What did you do to your Crew today?
- Replies: 367
- Views: 193172
Re: What did you do to your Crew today?
Today I'm gonna clean my MAF and hopefully find time to change an O2 sensor. Got a check engine light and had 8 codes. Can't tell you guys what the code #s were but they were MAF and O2 sensor related. On MAF, I recently swapped in a smaller k&n cone filter on the spectre intake tube. Got it, oiled ...
- Tue Jun 16, 2015 9:31 am
- Forum: Stock Electrical / Audio / Lighting
- Topic: Windows dont work ?
- Replies: 5
- Views: 1712
I'm shooting in the dark here, but based on that I'd check the harness that goes from cab to door. Sometimes only my drivers front stops working. Almost always either in the rain or snow or some other time I'd like it up. Seems to come back after a few minutes. My truck, in the rain, the wind and th...
- Mon Jun 15, 2015 8:55 am
- Forum: N.O.S. (Not Otherwise Specified)
- Topic: What did you do to your Crew today?
- Replies: 367
- Views: 193172
Sfa swap doesn't have to be big: http://i1067.photobucket.com/albums/u422/_STUCKY/zr5/BC59B52D-AA81-47C3-8DE0-0464C57E90A3.jpg I'm with approachnedium on this one, frame swap to get the longer cv's isn't worth the trouble. You'd be happier in the long run, and probably cheaper, easier, and better fu...
- Mon Jun 08, 2015 10:52 pm
- Forum: Tires / Lifts / Suspension
- Topic: 6" superlift wheel recommendations
- Replies: 6
- Views: 2140
No experience with the lift, but I was running pro comp 15x8 w/ 5 inch backspacing with 31s. The same size should work good with 33x10.5 (BFG km2 and I believe Toyo mt are available). I couldn't find the part number I had, but if you get on summit, narrow the search to 15x8 w/ 5 inch backspacing and...