S-10CREWCAB.NET

S10

I talked to a body shop, that is near me. They gave me a quote of $450.00. I have to supply the bed and the rear frame half and I do the prep work. Remove the bed, gas tank, and driveshaft. If I do this, it might be next spring. I have to find a bed and frame. Question, does the frame have to be an ...

S10

For thoses of you, that are using the steering wheel controls with aftermarket radios - which wire (from the truck) are you tapping the translate module into. My module is the PESWIAKJC from Peripheral Eletronics. Mine was working, but now it is hit or miss.

S10

Not to go off subject here - But what do all of those aftermarket gauges do and where did you get the orange key fob?

S10

I got to look at the sportside, yesterday, The bed is all steel and another thing that I noticed, as the bed sides goes towards the tailgate, the bed tapers in. Why would GM do that?

S10

The radio controls are in and working. I have the volume and mute programmed. I haven't decided on what to program the other three buttons to do. So they are dead, right now. On the airbag side of things, I had to change the connectors, where it plugs into the main harness. My truck is an 02 and the...

S10

O.K. I started to install the radio controls, for good or so I thought. I can't figure out, how to remove the airbag. I went and bought a repair manual (Haynes) :roll: and it is telling me that there are four spring clips that need to be push to the side, so the airbag will pop off. I don't see them...

S10

HenryJ wrote:I have no idea which bed would be lighter. It might be close. Aren't the stepsides fiberglass bedsides?

There is a stepside at work. I will ask the owner, if it is fiberglass.

S10

Just an FYI on how to test it off the truck. I am in complete agreement with you.

S10

There is a new guy at work, that used to work for a company that made custom quad axle dump trucks (WOW!). He said, to cut the frame, 12" in front of the rear cab mount, at a 45 degree angle. Straightest part of the frame, on most pick-ups. Do the same with the donor frame, in the same area. Grind a...

S10

I got the volume control buttons to work. Just a little cleaning and it started to work. I tested it with my meter. Here is a FYI - The Black and Gray wires are for the back lighting and the Green and Yellow wires are the signal wires. I just hooked my meter to the Yellow and Green wire, set the met...

S10

Correct! You will need to get a new receiver that will have this function.
One thing, I forgot to add to the post above.

S10

5 light switches and a rear power slider.

S10

I just installed my HD module to my Kenwood DDX-7019. I lot like it a lot. I think, I counted 40 radio stations, total. I like the fact that I can press a catagory button and it list the stations in groups. I press the rock button and all of the staitions that play rock will be displayed. The same t...

S10

It's not going to matter, which one is better. I was told by an XM rep, that starting some time next year, you will be able to pick and choose what stations from XM and what stations from Surius, that you want. Now that they are one.

S10

I messed around with the steering wheel controls, today. I wanted to make sure that they worked, before I made them permenent. It's a good thing I did. Because after I hooked the factory radio, back up and connected the controls under the dash. I started pushing buttons and the left side worked grea...

S10

Yep, I got. I just need to know what needs to be modified, since the years are different. BTW, you have been a great help and very understanding. Thanks! Don Z. P.S. Do you know if this forum is going to have a set up so you can post a picture right to the thread? Here is some information that might...

S10

Man, I feel like a noob! I believe we are on the same page now. I looked at the posted thread and not much to go on, there. So I leaved a note.

S10

My truck is a 2002. I have the controls from a 2004 blazer.
What are the modifications, that I would have to do, to make this work?

Thanks,
Don Z.

S10

No, the photos are on my hard drive.

S10

Yep! I can show you if I knew how to post a photo on here.

S10

My CC truck is a 2002. I have installed a Kenwood DDX 7019 touch face radio with all of the remote modules that go with it. I found a 2004 blazer in the salvage yard. It has factory radio controls, in the steering wheel. I took the steering column and all of the wiring that I could. I was wondering ...

S10

My truck is a 2002. It must be a late 2002, because I have the double din opening. I have the Kenwood DDX-7019 touch-face unit in my dash. It does fit with just the need of the adaptor brackets and no other mods to the dash. But, because of all of the wires that go to these touch face units, it will...

S10

I got the last piece to my console swap. The wiring! The only thing is, that one side had to be cut off. Now I need to rewire that end and I don't know where the wires go. I just hope all of the shifters are the same, since the wiring is not the same year as my truck. This is the wires that I have -...

S10

Yes!! The problen is solved. I was in the middle of the shifter console swap, when I found it. It was the pink wire, up in the column. It had the insulation rubbed through, from being to tight. Maybe, I use the tilt to much.

Thanks for the help,

Don Z.

S10

I am still looking. I need to get the ignition key housing off the steering column. Can this be done without removing the steering wheel? I have ruled out the red wire going to the ignition key. I think it's going to be a pink wire and it is up in that housing. I had the fuse pop on me, again and it...

S10

For those interested, I went to the dealer and got some info, on the shifter cable. The console is DO7 opition code. The transmission with electronic transfer-case is opition code NP4/NP8. The shifter cable is part # 15189203. I order my shifter cable from this web site for $68.15. http://www.tradem...

S10

O.K. Thanks! I will look in the morning.

S10

No. The alarm was attached to it. But it has been removed.

S10

The diagram on box lid says "Ignition" and there is only one 40 amp fuse in the truck.

S10

The big orange 40 amp fuse, under the hood.

S10

The 40 amp fuse keeps popping and it's at ramdom! I thought it was the aftermarket alarm, so I had it pulled. Still popping the fuse. The second time, it popped, I saw a little puff of smoke, come out from under the dash. Any ideas what it can be and what is on this circuit? Any help in this matter ...

S10

I was at the salvage yard, today. I went looking for manual steeering columns. I saw two 97 columns.
I know the steering wheels different than my 2002. But would the covers, that are on the column, work to cover up, where the shifter was on my column?

S10

I just won a floor shifter/console on E-bay. So I am going to keep my eye on this thread.

S10

It appears that yesterday's Crisis is today's low priority :roll: For some reason, I could not log on to the website yesterday. I am looking over what everyone has written so far. I will be looking at the pinch weld today. I did notice that the rubber strip that runs along the bottom of all the win...

S10

Yes, I saw the bubbles appear with the A/C running. It is mostly the front windows, near the mirrors.

S10

The bubbles are on the corners of all of the windows.

S10

I have a 02 S-10 and when the windows are up, at highway speeds, I get wind noise. I thought it was the gaskets around the doors, so I replaced all of them. Then I was at a car wash and had the A/C running that day. I noticed soapy air bubbles forming at the corner of the windows. So now I know wher...

S10

Thanks to everyone, for the info. I guess I will be adding a 2" body lift.
And thanks for the warm welcome to the forum!

S10

BobbleSmitty wrote:Hey welcome to the site. I'm from the east side of Cleveland and have a black S10 crew cab as well. What part of Cleveland are you from??

I am on the west side. West Blvd.

S10

Black 2002 Crew Cab! Is there a reason why only a 2" body lift is avaliable?

Thanks for the Welcome!

S10

Is it easier to get at the middle spark plug, on the drivers side, with a body lift? I noticed how difficult that plug is, due to it being behind the steering shaft. Also, how much lift can I get, for the body. All I see is 2" kits. My old S-10, I was able to get 3" and it was cheaper. BTW, I am new...

S-10CREWCAB.NET

Search found 41 matches

Next on my radio upgrade todo list!

Popping 40 amp maxifuse! Not good! solved

Wind noise problem?

Question about body mounts

Search found 41 matches

Next on my radio upgrade todo list!

Popping 40 amp maxifuse! Not good! *solved*

Wind noise problem?

Question about body mounts

Popping 40 amp maxifuse! Not good! solved