S-10CREWCAB.NET

D68enny

I wonder if you have to buy both kits to get one complete kit.

D68enny

I have 31 X 10.5 tires with 4 in. backspacing on the rims. I have one spacer on back to match the width of the front. Pictures can be seen. ALBUM I used a air hammer to Pound back the inside of the rear outer fender well and put some of that black window weld that was said to be used on the skidz fl...

D68enny

Sorry man I forgot to post the link.

http://performance.drivewire.com/suspen ... tkits.html

D68enny

I have 31" Kumho MT's on my truck with shackles, body lift and TB crank. I had some rubbing issues that I let go for about 4 months then decided to fix. The tires were rubbing on the plastic front bumber and on the outer rear part of the front wheel well. Everything is fixed and i have no rubbing wh...

D68enny

I fell upon this web site while searching for a 6in Superlift. Does this sound like a regular Superlift kit or what? Price is very good and then there is free shipping. Am I missing something?

D68enny

I figured I could put them on back. They are from a different vehicle but they are good tires except for the slight feathering on two of them. Thanks guys.

D68enny

I have a set of tires, but two of them have slight feathering. Can they still be used? Tires still have about 85% tread on them. Will they were back to normal tread wear if alignment is correct?

D68enny

HenryJ: Perhaps the problem is elsewhere? Perhaps the relay wiring or the lights? I have not thought about the relay or the lights because the original switch that came with the KC lights works fine. I turn on the switch, the lights come on and the little light on the switch comes on. That switch is...

D68enny

HenryJ Wrote: Sounds like you have the load and supply reversed , or the supply and ground.Do you have a multimeter? I have one somewhere, but I do not know who to use it that well. When I switched the load and supply the lights come when the switch is turned on normally, but the light in the switch...

D68enny

I will let it sit for a few days and see what happens. At this point I am clueless. I want to blame the switch, but I don't think I would get a switch from the company that has wrong internal connections.

D68enny

f9k9 Wrote: You can use low amp smaller gauge wire to your switch. All it does is light your switch, if applicable, and send a signal to the relay which should have come with your KCs. The hot wire to your relay should be 12 gauge and fused with a 30A fuse. That is if, I understand what you are aski...

D68enny

Ok when I hook it up that way I connected the SUPPLY line to #5, the LOAD line to #4, and at that point the light on the switch would be on in the off position and when I turned the lights on the KC's would come on and the switch light would go off. All with no ground connected. Then when I hooked u...

D68enny

Ok this may be a pain in the arse thread, but I am going to give it a shot. I have my KC lights hooked up and they work with the three prong switch that came with the lights. On this set up the is a Green (load) line that hooks to the switch and runs to the relay which goes to the lights. The next l...

D68enny

Thanks HenryJ. I have that part done. I have another question about the wiring. I am installing two 150 watt KC lights and the kit comes with factory wiring. The problem I just encountered is that after running the wires over to the passenger side and then back over to the drivers side on the inside...

D68enny

I am trying to run some wiring through the firewall and have read on the site that the easiest place to run them through is the hole for the antennae wire. My question is where does that wire run through on the firewall side of the engine bay? Does it come out right under that big black plastic case...

D68enny

Ok I have another question. I have looked at the Crane HI-6 and it says the compression ratio should be between 10.1:1 and 14.2:1 (somewhere in that range). Our trucks have a low 9.1 don't they? Are the Crane HI-6 even compatible with our trucks? They are cheaper off of Ebay, but I don't know if it ...

D68enny

HenryJ is that all 94 and up S-series or is the extended cab S-series a better choice to hunt down?

D68enny

I have a question about these aftermarket ignitions. When you hook one up with no rev limiter do you loose the fuel cut off or rev limiter you all ready have stock?

D68enny

Thanks for the pics. I will install it this week some time.

D68enny

Yes Steve, I would love some different angle shots. Did you make holes big enough for the main mounts to go through the plastic and come in contact with the metal when you tightened them up, or did you just mount up against the plastic?

D68enny

I don't know if i am going to install it now. The way it should fit i don't like to much, and the way I want it to go on puts those tops bars right up on the headlights. They cross over in front of the turn signals and almost sit up against them. If I mount it that way I may have trouble getting the...

D68enny

Well I figured out what happened and it was not good. I burned up the 3rd and 4th clutch packs. They burn out quick when something is not right. I only drove the truck like 1.5 a miles total from the first servo install to about the tenth time I reinstalled it trying to figure out what was wrong. Th...

D68enny

Ok Thanks, I thought it was to good to be true. There is nothing bolt on about it. Then there were no directions to get any ideas from any mounting locations. I thought this install was going to be a breeze.

D68enny

I just got the 53-1002 Eliminator light bar from Off Road Innovations and I am wondering if anybody knows about installing it on a 02 Sonoma. It does not look like a direct bolt on item like I thought it was supposed to be. I have a 2" body lift, so could that covering the main mounting holes I shou...

D68enny

I tried the spring trick and no luck. Is it just the servo cover O-ring that is supposed to be hard to get out? What about the other O-ring? I was able to get them all out ok the first time I took it apart. If the O-rings look good and feel good do you think they are ok to still use? I am trying to ...

D68enny

I'll give it a shot. I am hoping that that could be it. I feel the spring just sat in the right position, but I would love to be wrong. I will tell you on thing. I am one servo changing mo fo now. I can pull it out re-configure it and put it back in by myself with a prybar and screwdriver in 10 minu...

D68enny

I put the sprind on the pin and slipped it on. I have had the servo in out out with different configurations of new and old parts and nothing has changed. I just put everything stock back in and still no go. I was wondering if the servo pin could have been pushed in to far with that one servo being ...

D68enny

The servos were the only thing I messed with. I am going to put everything back to stock and see what that does. The last thing I did was put the stock 4th servo back in and kept the super servo in, but had the same results as above. I will go back to all stock and see what happens, but I think the ...

D68enny

Can anybody find me a diagram showing the order of parts for the OEM set up for the servo in the 4L60E transmission. I can not remember the original set up and need to try and put it back to stock to see if i still have the same problems listed in the thread below. Thanks.

D68enny

Griff, Did you have to grind the washer down for the sonnax to fit properly, or is the corvette servo still considered an OEM item? I think I screwed something up in my transmission. I now have 1st gear and 2nd gear working ok. Firm shits, normal shift points, but when it gets into third it slips un...

D68enny

Here is a link for the Sonnax 4th gear servo. http://www.powerglide.com/parts/parts/77767K.htm I cannot find the directions online for the Superior Super Servo #k012. I guess I will call both companies tomorrow and see if the is a compatibility issue with these two parts. I thought when I found the ...

D68enny

I still have problems. Even after turning the 2nd apply servo around I still have 1st gear with a long hold and then after that my transmission just slips in the other gears. I have red on the fine print of the Sonnax 4th gear super servo that it is compatible with original equipment 2nd apply servo...

D68enny

Ok I am embarrassed to say this but I had the second apply servo in backwards. I usually don't make stupid mistakes like that. People have told me though that your mind will change when you have a child and my kid is two and a half now. He wears the mind out sometimes. I want to thank everybody for ...

D68enny

Ok now my problem has changed a little. First gear still holds at real high RPM's even at normal driving take offs. Now it slips into second and the transmission is not locking up all the way. It slips in 2nd, 3rd, and 4th. I put it into first and it is fine. Something has to be wrong with the insta...

D68enny

I also have a HPPIII programed in there with the firmest shifts. I am very unfamiliar with how these servos work. I do have firm shifts when just driving normally, but if I step on it from a stand still it will stay in first gear until it redlines and the fuel starts to cut out if I don't let off th...

D68enny

I just installed a corvette servo and a billet 4Th gear servo and a longer pin. Now when I floor it 1st gear holds until redline unless I let off the gas a little then it will shift into second. Then when I am cruising at about 35 and floor it, it does not feel like I am shifting into 1st gear or th...

D68enny

What we are talking about is when you do the skidz flare mod from the modification page it says use some dry window weld urethane to seal the cut pieces toghether. I am using it to covere the bare metal I cut away from the front fenders to put on my 31 in tires and to seal the wholes from where my m...

D68enny

I looked at their website and did not see anything, but that does not mean crap. I thought they should have it, so maybe it has another name.

D68enny

Where can you get the window weld urethane stuff for the flare cut outs besides online? Autozone, Walmart, Homedepot? Any of these spots? I am trying to get it tonight, but don't know where to search for it. Thanks

D68enny

I may have to do the work shipping thing. I am always hauling ass home to see if something was delivered, and to keep my wife from seeing it first. It sucks when something takes like 2 extra weeks to be delivered. Hey Steve2003, Where did you get your light bar? I have been looking around for an ORI...

D68enny

Your truck looks great. The flares make it look so much better. Did you do the fender mods just like the directions on the modification page? I was thinking I will just do the fronts for now and wait a while until my wife cools down from buying the wheels and tires and then get the flares. Thanks fo...

D68enny

I think the ZR5 was throwing me off. The have a different looking factory flare. It looks more rounded and is black. The regular crewcabs I think have body colored flares.

D68enny

Hey Wamason. Are those the factory flares on your truck? When I look at your truck it just looks different than mine. My flares are more squared off and blend in more. I have some kind of molding on the sides of my truck. I am trying to find a picture of a Sonoma to compare.

D68enny

So you mean on the inside part of the wheel well? Can trimming and hammering be done to fix this and have it still look ok? I just spent my last bit of cash on a Hypertech. I thought the wheels would clear so I spent what was left of my state tax return to fix the tire size change with a Hypertech. ...

D68enny

Never mind I just saw on this thread they rub in the front.

D68enny

So if I can keep this baby running in a straight line with no bumps I am good to go as is. Do the fronts rub on the front or back of the fender? Thanks for the info. I was not looking forward to this.

D68enny

I just ordered some new black steel wheels and they are 15X8 with 4 inches of backspacing and -12.00mm offset. I am running 31 x 10.5 x 15 Kumho mud tires on the new wheels. Currently on my truck I have the stock wheels and tires with 2 inch rear spacers and 1.25 inch front spacers. I have the 2 in ...

D68enny

Ok, Thanks. I thought this was the case, but wanted to check with everybody and make sure. It is the factory installed hitch and I was going to redrill the hole and move it up at a later point after the install. I think that should be ok. Thanks for everybodies help.

D68enny

Has anybody installed a body lift with a factory tow hitch? If so does the hitch still sit in the same factory position, or should it raise up two inches with the rest of the truck? I don't see how it is going to raise up. I stopped at this point to figure out if I am missing some brackets or if jus...

D68enny

That is what I thought. I thought I remembered you saying something about the plyability of the stock flares soemwhere, but I could not find it. I may just go flareless for a while. Thank you Henry.

D68enny

Does anybody know if you can use the cut out templates offered by HenryJ for the skidz flares, but use the factory flares somehow to fit in the new wheel well. I have everything I need to run 31's, except tires and flares. Will factory flares bend to fit the new cut out? I will have the money soon f...

D68enny

I have read in a few places that the Challenger is going to have a 6.1L engine and produce 425 hp. I would like to know the torque on both the Camaro and the Challenger. I would assume a at least 400 ft/lbs for both. The wheel sizes are getting a little out of hand. I have not even looked at the pri...

D68enny

That is it. Thanks for the info guys.

D68enny

Is it the 4L60e? I am thinking that is it, but I need to know for sure. Thanks.

D68enny

What transmission is in the 2002 crewcabs?

D68enny

Is anybody running Gabriel Max Control shocks? I did a search and it turned up 1 result from a couple years ago. Nothing said there about them. They look like good shocks, and they have a buy 3 get one free deal going on. Auto Zone has them for 49.99 each. Not a bad deal, but want to find out more i...

D68enny

I am looking to buy some wheels, and the backspacing on them is 3.25". I am a little worried about this because I have not seen anybody mention this little bit of backspacing on their new wheels. I am going to try and run 31 x 11.0 x 15 super swamper thornbirds. I have a 2'' body lift, 2" shackles, ...

D68enny

Does everybody with the body lift use the gap guards? Does it look ok without them?

D68enny

Does everybody with the body lift use the gap guards? Does it look ok without them?

D68enny

The wheels have 4.5 inches of backspacing. I think it will be ok.

D68enny

Does anybody know or think the Super Swamper LTB 34 x 10.5 x 17 will fit under my 02 with the 6 in Superlift? The outer diameter of the wheel is 33.8 inches and the width is 10.3 inches. Tread widthis 9.3 inches

S-10CREWCAB.NET

Search found 61 matches

Superlift Cheap. Too Cheap?

Tire Feathering

Wiring Help for KC's

Running wires through firewall

ORI light bar Installation

Diagram of factory servo assembly

Need Help With Corvette Servo and Billet 4Th Servo

Window Weld Urethane

New wheels need help

Nedd Help with Body Lift

Flare Cut Out Templates & Stock Flares

Which transmission

Gabriel Shocks

I need help. Is anybody running this backspacing?

Will this fit?