S-10CREWCAB.NET

_STUCKY

That is what I thought as soon as I hooked the ground up like the diagram and it didn't work. But I checked and they are in the way the diagram shows. I did notice that if I touch the test light to the green wire, the lights come on/off. It also is very faintly lighting the test light. This tells me...

_STUCKY

It works.... Kinda.... So I wired up the washer fluid button using 4 relays and 2 diodes: http://i1067.photobucket.com/albums/u422/_STUCKY/zr5/62632C63-23EE-43FD-A559-0DB5566EBB94-839-000002A37AF439F5.jpg This is from here: http://www.the12volt.com/relays/page5m.asp#_index I can only get the button ...

_STUCKY

Here is a technical spot. I had a better line in the second picture. http://i1067.photobucket.com/albums/u422/_STUCKY/95%20yj/2EFAA862-363C-4D2F-B8F7-039A564ED9A7-10200-000013AED738D77B.jpg http://i1067.photobucket.com/albums/u422/_STUCKY/95%20yj/38E8147F-6FB4-4206-ACD5-401800FA737F-5836-00000C4766C...

_STUCKY

The washer fluid button will not make a connection unless the wiper switch is on. Take the switch apart and cut the little plastic "wall" on the top right side to allow the button to make a connection in any position. I used a dremil. http://i1067.photobucket.com/albums/u422/_STUCKY/zr5/DD87700E-278...

_STUCKY

We usually get a cheapo from NAPA. They seem to work ok, but when something happens to it, we just get another. We probably have a pile of 10 of those lil junkers. The last one, the bolts wouldn't stay tight and it would spit oil all over the place. I've also seen them snap off the 1/2 square that t...

_STUCKY

If you want weatherproof, find a few different cavalier/sunfires in the junkyard that have had the GM starter fire recall thingy. They are bolted to the core support on the engine side. Super easy to remove and 100% weather resistant/proof. Roughly what year range? And how many relays do they have?...

_STUCKY

Fingers crossed!

_STUCKY

http://www.the12volt.com/relays/page5.asp#lsp HJ, would you look this over again for me, purdy purdy please with cherries and such. I just want to double check before I try wiring anything up to the truck. The 4 relay with 2 diode method is my goal. The new plan is to use the "Rear hatch" button to ...

_STUCKY

If you found a BCM from a Blazer, or Bravada with tow/haul and fogs, you would be all set to use the stock wiring. The BCM takes care of latching the circuit. I will keep my eyes peeled. If I go that route, I assume that I will still have to wire up the window washer and rear hatch buttons with rel...

_STUCKY

So.... To get the 3 momentary switches (factory fog lights, rear hatch, and washer sprayer) to be on/off switches, I would need 12-15 relays?

That does not sound like any fun...

_STUCKY

http://www.s10forum.com/forum/f136/98-s10-blazer-fog-light-wireing-help-436542/ the wiring for the switch is behind my dash plugged into a dummy port, i got a new switch, and installed it, there is a fuse relay for fog lamps in that box under the hood, but i cant find the wires in the front end for ...

_STUCKY

What do I need to know about using the fog light switch on the left side of the steering wheel in a truck that doesn't have fog lights?

I planning on using it to switch lights in the bed.

_STUCKY

http://m.youtube.com/watch?v=qY5ZOJcFgjI&feature=m-ch-fea My buddy did this all with some app on an iPhone. It took maybe 10 minutes to do. If nothing else, this shows how NOT loud it is. As you could see at the end, my tires are a lot louder. We would have done an in cab sound clip, but I don't thi...

_STUCKY

It shouldn't be getting too hot. I was actually really surprised. It was a 45 minute drive home, and when I got home, the first thing I did was put on a leather glove and go touch the end.

Warm, but not anywhere near as hot as I expected.

_STUCKY

Well, it's not under the bumper, it's just barely under the hitch. It's still tucked up nice and high. As for the routing, the guy's bender can't make a bend over a bend. Once the pipe is crushed at one angle, it had to be moved to where the end of the die was at the end of that bend to make another...

_STUCKY

We got it taken care of. The guy cut the flange off right behind the cat and welded it from there back. Instead of routing it over the leaf spring and out right there, we went around the spare and out just under the hitch. It sounds good, but not loud. I'll get some pictures and hopefully a sound cl...

_STUCKY

Also, on the page with all the mods to that truck listed, it says "removed pre-cat".

Should I?

Edit: I have an 18 inch Magnaflow with 3 inch in/out

_STUCKY

HJ, I got questions :? I was told that 3 inch tube in the stock location won't fit. The guy claims he is going to have to "run it out the back". I tried telling him that it appears to have plenty of room. I have an appointment scheduled for 8 in the morning. Was yours unbolted from the back of the c...

_STUCKY

F9K9 wrote:Not a smart comment and one you'll live to regret. Better button up your aerial defenses ASAP!

I try not to abuse it too awfully bad

_STUCKY

I am guessing that you are not referring to the one that I have the red wire hooked to?

_STUCKY

Honestly, a solid axle swap would be easier. I'm not saying don't give it a try, but like AVTekk said, it may never drive the same again. An XJ high pinion Dana 30 front axle, with an explorer disk braked 31 spline 8.8 rear axle, would be a much better setup. Parts are ridiculously plentiful. Afterm...

_STUCKY

If you are adding more than the small light that I added , a relay would be a good idea. It can be activated by the same wire that I used. I would mount a relay inside the rear frame rail near the tail light wiring. Inside the left rear frame rail there is a white plastic connection. This is the ta...

_STUCKY

I did that a while back when I had a low beam go out.

_STUCKY

It all seemed to be working just fine.

Although, my lady friend says it took me longer than 10 minutes. She is a champ, though. She sat in the truck while I was doing all the wiring.

_STUCKY

Thank you!

_STUCKY

whoa! That was fast Brule! Lol

Yea those things are junk. But that's the concept, correct?

_STUCKY

So, I let me get this straight... HenryJ wrote: Splice tap the green w/white wire (high beam +) attach to relay "activate +"(#85) , Splice tap the yellow wire attach to relay feed (Normally Open #30) , attach a wire ,or wires, to a good ground and connect it to the relay supply (#87) and to relay "a...

_STUCKY

I read on here that GM deleted the glove box light on some models. So, while pillaging interior parts from a 98 Oldsmobile Bravada, I pulled the glove box light. One would think that GM would have left this seemingly pointless little detail alone. Whilst wiring a glove box light into one of these tr...

_STUCKY

http://i1067.photobucket.com/albums/u422/_STUCKY/zr5/77D7D2DF-F286-41BF-970D-769E42A1BD99-10838-000015F085464EEE.jpg My brother sent me this. Yesterday, I was sent out into one of our fields with a catapiller tracked tractor. It was very muddy. Tracked tractors and mud do not mix very well. What I ...

_STUCKY

Check the codes in the glove box to see what gear ratio you currently have. GT4 Axle Rear 3.73 Ratio (Dup with 5X1) GT5 Axle Rear 4.10 Ratio (Dup with GT8) GU4 Axle Rear 3.08 Ratio GU6 Axle Rear 3.42 Ratio Your front axle is open. You should leave it open. Only 1 tire turns. It will be the tire with...

_STUCKY

I looked at the wiring harness. There were no orange and black wires exiting the bundle. The only two exiting the bundle went to the courtesy light below the dash (red plug) and the yellow plug in direction of the firewall that you see in the picture. http://i1067.photobucket.com/albums/u422/_STUCK...

_STUCKY

http://www.shockwarehouse.com/site/prod ... ries-Truck

http://www.shockwarehouse.com/site/prod ... ries-Truck

_STUCKY

I do not know. I am still new to these truck. And honestly, I'm not much of a motor guy. All I know is whatever your truck does can be fixed. It could also have a motor swapped in. But I think you could get an AC delete pulley and exnay all the AC stuff. It might give the illusion of putting the hor...

_STUCKY

Hey, that reminds me! Check out this: http://www.pirate4x4.com/forum/chevy/1174577-99-zr2-sfa-ls2-project.html By no means does that go into much detail about how to do it, but it does show that it can be done. However, I see 4.3s on Craigslist almost every day in the $200-500 range. I would think t...

_STUCKY

I'm going to drive around for about a week to see if the intake has any effect, by itself, on fuel mileage. I got the ball rolling today on the exhaust. I have a buddy who has been doing some side work at a local fab/hot rod/ basically anything automotive shop. I've heard through the grapevine from ...

_STUCKY

I got a little done to the truck today 8) http://i1067.photobucket.com/albums/u422/_STUCKY/zr5/D471A519-0413-462D-9D7A-3F67BF7E135F-8224-00001218DAF6254D.jpg http://i1067.photobucket.com/albums/u422/_STUCKY/zr5/D852DED1-313A-46BC-82E7-91BF52539C10-8224-00001218F0A1FB2E.jpg I may have been motivated ...

_STUCKY

All those bugs could get worked out, but we are cluttering this thread lol

_STUCKY

I got skid plates, with brackets! Not too sure if the gas tank skid is gonna work. Payed $80 for the full set, which is $5 less each than the junkyard wanted. Also, I picked up an explorer front driveshaft for my jeep. I'll need one for when I finally get the sye in the np231 and the 8.8 in the back...

_STUCKY

He was not in the mood for pictures lol

I'm off to pillage a Craigslist find. Guy has 3 s10s, I got a buddy that needs parts, I want skid plates, it's nice and wet out, wish me luck.

_STUCKY

I just pulled my dads 01 dodge cummins extended cab long bed 4wd out of the mud with my s10. It surprises me more and more everyday.

_STUCKY

The motor would bolt to you tranny and motor mounts, but I believe it's an older version of the 4.3. I think it's a different fuel delivery setup. I vote 5.3 for you lol. I saw one on clist today for $500

_STUCKY

http://forums.s-10crewcab.net/viewtopic.php?f=4&t=8786 Look at this. Click some links. Do some reading. I am really enjoying mine with tbars turned up, Boise Springworks kit, 15x8 with 5 inch backspacing wheels, 31x10.5 tires, bilstein shocks, poly sway bar bushings, full size bumpstops on the front...

_STUCKY

Hey Reed, my dad has a corn furnace at his house. It's been there for I'd say 5-6 years now. He really doesn't use too much propane, since the stove is the only thing that runs on that all the time, maybe the water heater too. Basically, it warms and circulates antifreeze. I don't fully understand i...

_STUCKY

Does it have aluminum skid plates?
Where is it located?
Will you ship parts?

Edit: Any info on that jeep in the 4th picture?

_STUCKY

I'm having troubles linking the pictures, but check out these builds. The main focus of this thread is not the chopped top. Post #109 has a good side profile picture. This one is a 4 door blazer on a full size frame with the back cut off. http://www.pirate4x4.com/forum/chevy/936391-90-chevy-truck-96...

_STUCKY

Is there enough room between the spare tire and the rear bumper to mount the compressor? Or maybe in front of it?

Pictures. .... We are gonna need pictures...

_STUCKY

My secret weapon:

Don't tell all the guys with tents...

_STUCKY

That's the plan!

Edit: ......

..............oh, and not freeze to death......

_STUCKY

Attica bound.

_STUCKY

Stucky PLEASE for the love of everything, NEVER recommend airbagit.com, Chassis Tech, AIM, or any of the related companies for air parts. Everything they sell is absolute junk, it is well known to stay away from them in my industry. Their metal parts are usually ok tho. I am not schooled in the way...

_STUCKY

What are you pulling? I have pulled several heavy pieces of farm equipment with the BSW kit without any issues, and no complaints about the ride, with or without it loaded or pulling. If you aren't afraid of the work, and possibly the trial and error, we could walk you through making your own leaf p...

_STUCKY

Just wanting to double check this, but do ZR2 springs bolt in? I haven't found anything confirming or denying that they do. It seems most people just do a shackle lift, instead of messing around with the leaves. Edit: Ah jeez.... http://www.s10forum.com/forum/f19/zr2-rear-leaf-springs-same-as-reg-4x...

_STUCKY

Can that get eliminated, like on jeeps and older Chevys? I got a 4.0 in my Comanche that I just went and got a couple of these and stuck in the hole. I literally had to stand on them to get them in. Some jumping may have been required, as well as some stomping. I assure you, I care less about that C...

_STUCKY

What about the manual diff lock cable? I have a feeling they would look at that as not so hardcore. Those kinda had a bad rep in the early years for being problematic, not just on the s10 though. Jeep, chevy, dodge all used a disconnect of some kind through the years. I know there was a redesign at...

_STUCKY

Yea it's kinda hard for people on there to give a straight answer. They hate it when knowledge is shared. It does serve its purpose though as far as modifing any platform into a toy. There is a lot of good information and amazing build threads on there. There is always gonna be those people that jus...

_STUCKY

On pirate there has been a lot of s10 questions getting asked lately. The pirate crowd, is, lets just say, not as friendly as it is over here. Granted, a lot of the time the questions are rather silly. The thing is everyone just flames away and tells people to go to another site. Well, the pirate ru...

_STUCKY

If nothing gets mangled on mine when I take it all off, you are more than welcome to it. I won't get a chance to mess around with it for a while though. I've been running around like a chicken with my head cut off trying to get ready to haul my jeep to Indiana next weekend. It's been cold, and right...

_STUCKY

I haven't had time to mess with any of it yet. Can you post pictures of what broke?

_STUCKY

31" BFGs 2" BL Skidz Fender Flares Skidz prototype front skidplate Rancho shocks Cragar 15x8 Rockcrawler wheels with 4" BS <- I did the 1st gen centercap mod with these WAAG pushbar from a trailblazer w/ KC lites Black nerf bars Billet grill inserts Bed caps Custom tow hitch The only that that chan...

_STUCKY

http://m.youtube.com/#/watch?v=J3i7EFYk ... 3i7EFYk-_c

That's my first thought....

However, I thoroughly enjoy my heated power leather seats that I recently pulled out of a 99 olds bravada. The 60/40 bench that was in the ~01 extended cab my dad had wasn't too bad.

_STUCKY

Maybe try scratching it to see if it will flake off?

I'd rock a black bottom. I'm looking forward to seeing what you come up with.

_STUCKY

Does anyone have a current coupon code for shockwarehouse.com ?

_STUCKY

So you didn't get either one yet?

_STUCKY

I changed the link to go to the red filter instead of the black one. Hopefully, no one else has a problem ordering it. By the way, I suggest calling instead of ordering online, and asking lots of questions. They are there to answer your questions and send you the parts you need.

_STUCKY

Just see if they can change the order to a different colored filter.

9901 red
9901W white
9901K black
9901B blue

http://www.spectreperformance.com/index ... lt/?q=9901

_STUCKY

It shouldn't be bad. Just have to find someone that you are confident in bending and welding it all up.

_STUCKY

The different part numbers are just the color of the filter. I wonder why they didn't set you up with a different color.

_STUCKY

I don't know. They told me that both were in Ohio on Sunday. I ordered the intake Saturday, the muffler Sunday. I got the muffler yesterday, and the intake today. Tell me how that works?

_STUCKY

Summit sent me a catalog today with part # HYP-30012 Truck/SUV 4.3/4.8/5.3/6.0/8.1L for $99.50 with free shipping. I am guessing this is what would work on your truck and the S10s?

Edit: it says not available
http://www.summitracing.com/parts/hyp-30012

_STUCKY

killian96ss wrote:
_STUCKY wrote:UPS just dropped mine off.
Like a kid in the candy store, I know the feeling!

Steve

Yea, but, Mama says I can't eat any candy today!
.
.
.
.
.
Valentines day....

_STUCKY

Check this out. Made in California my... Donkey!

Hecho en China!

_STUCKY

UPS just dropped mine off.

_STUCKY

Bump!

_STUCKY

I almost forgot about the Ammo cases. I looked at all the army navy stores around here and they think I am crazy. I guess I need to order them online. I could def use some storage space in the CC with all the little goodies I keep in it. Like the portable air compressor, first aid kit, some small t...

_STUCKY

Well here is what I did today. http://i1067.photobucket.com/albums/u422/_STUCKY/zr5/420512b6.jpg These boxes were made to hold 32 40mm cartridges. I got them at the local army surplus store. They are a perfect fit between the wheel wells and the boxed part at the back of the bed. I used 4 of the bo...

Search found 851 matches